Results for10mm pellet manufacturing equipmentfrom 69883 Products.
|
Terminal probe Reference Standard: IEC62368-1-Figure V.5 Technical Parameters: 1, Test Probe Length :13mm 2, Test Probe Diameter:1.0 (0, +0.005)mm 3, Dam- sphere Diameter:35mm 4, ...
|
|
|
|
Diameter 60mm Test Rod , EN 60335-2-30 Surfaces that are accessible to the test rod Product Description: 1. According To Standard: EN 60335-2-30 2. It is used to the protective ...
|
|
|
|
IEC60529 IPX1-6 Waterproof Degrees Test Equipment Ingress Protection Test Chamber Product Introduction IPX1/2, IPX3/4 ,IP5/6 waterproof degrees test equipment are designed and ...
|
|
|
|
Limited short-circuit test , IEC 62368-1-Annex R R.3 Test method The source shall be applied to the EUT via the mains cord supplied or specified by the equipment manufacturer. ...
|
|
|
|
IEC60529 IPX1-6 Waterproof Degrees Test Equipment Ingress Protection Test Chamber Product Introduction IPX1/2, IPX3/4 ,IP5/6 waterproof degrees test equipment are designed and ...
|
|
|
|
UL Rain Test Apparatus Test Equipment: UL Rain Spray Test Apparatus for Outdoor electrical enclosure waterproof test Applicable Standards: UL1598 / CSA250, UL50E / CSA 94.2, UL ...
|
|
|
|
The en60900 hand tool high temperature pressure test device is designed and manufactured by Dongguan safety regulations according to the standard en60900 Figure 18.The en60900 hand ...
|
|
|
|
IEC60529 IPX1 IPX2 Tester Ingress Protection Testing With Water Filtration Unit Product information: This test device is to verify Protection against Vertically Falling Water Drops...
|
|
|
|
Test pin, IEC 60335-2-80-Figure 102 Test pin Key A stopper pin B full thickness section with length at least equal to that of the original bolt C reduced thickness section with ...
|
|
|
|
ZR-1210model respirator resistance detector Product introduction Zr-1210 respirator resistance tester is used to measure the inspiratory and expiratory resistance of the mask under ...
|
|
|
|
Impulse test generator circuit 1 of Table D.1. 1950S pulse generator, is a test instrument for generating pulse signal and HVDC signal. This instrument is designed and manufactured ...
|
|
|
|
Impulse test generator circuit 2 of Table D.1. 1950S pulse generator, is a test instrument for generating pulse signal and HVDC signal. This instrument is designed and manufactured ...
|
|
|
|
Kettle Plug Tester With Touch Screen PLC Electric Control System Product information: The kettle insert-withdraw endurance test device is designed and manufactured according to the ...
|
|
|
|
GB/T4288-2008 Electrical Appliance Tester Pipe Bending Tester For Washing Machine , Drain Pipes For Washing Machines Tester Product information: This tester is according to GB...
|
|
|
|
Microwave Oven Door Endurance Tester Product information: The microwave oven door endurance tester is designed and manufactured according to IEC60335-2-25. It is a dedicated tester ...
|
|
|
|
Cord Anchorage Torque Tester / Power Cord Tension and Torque Tester Description: This device is design and manufactured accord to the requirements of IEC 60335-1 clause 25.15, ...
|
|
|
|
IEC60068-2-75 / GB2423.55 Standard Spring Hammer Calibration Device for Spring Hammer Calibration Product Description: Spring impact hammer calibrator is based on all parts ...
|
|
|
|
Temperature Measurement Heating Test Corner For Temperature Test Of Electronic Product Product information: The temperature measurement corner conforms to the standard requirement ...
|
|
|
|
IEC60335-1 Stability Test Turn Table With Digital Inclinometer / Inclined Plane Device Product information: This device is designed and manufactured in accordance with the IEC60335...
|
|
|
|
Conventional Cordless Kettle Boil Pour Dry Heating Withdraw Fully Functions Tester Product information: The electric water kettle tester is suitable for comprehensive lifespan ...
|
|
|
You may also be interested in :