Active Member
|
[China]
Address: 2# Jinlong Rd. Baolong Industrial Zone, Longgang Dist. Shenzhen China 518000
Contact name:Tarik Lu
Force sensor torque transducer |
|
|
Shaft-to-Shaft Rotary Torque Meter 0-500Nm Rotating Torque
Measurement Transducer
Shaft to Shaft Dynamic Torque Sensor FY01 is a slip-ring type torque transducer intended for rotating
torque measurement,Slip rings are used to conduct the millivolt
signal from the wheatstone bridge bonded on the sensing shaft which
will rotate together with motor shaft in both clockwise and
counterclockwise direction to get the torque measured. Rotary Torque Meter FY01 offers 0-10NM / 0-20NM / 0-30NM / 0-50NM / 0-100NM / 0-200NM
/ 0-300NM / 0-500NM eight rated measuring ranges with maximum 0.2%
non-linearity of the full scale to choose from. Keyed shafts
located on both ends of the sensor can be connected to motor and
load through couplings.Rotating speed of model FY01 can go up to
4000RPM,it is also suitable for non-rotating and low-speed torque
measurement applications.Signal conditioner and display unit is
also available to get the readout or 0-5V/0-10V/4-20mA
output.Typical applications for this type of torque transducer are
for example servo motor torque measurement, test bench
applications, valve torque test, torque measurement for stirring
devices, screw driver calibration, twist measurement, actuator
test,etc..
Dimensions(unit in "mm")
| Ordering code | Measurement Range | Torque direction |
| FY01-10NM | 0-10Nm | Clockwise & Counterclockwise |
| FY01-20NM | 0-20N*m | |
| FY01-30NM | 0-30N-m | |
| FY01-50NM | 0-50Nm | |
| FY01-100NM | 0-100N*m | |
| FY01-200NM | 0-200Nm | |
| FY01-300NM | 0-300N-m | |
| FY01-500NM | 0-500Nm |
Specifications
| Capacity | 10N*m / 1kg*m / 89lbf*in |
| Rated output | 1.5mV/V |
| Excitation | 3-15V |
| Zero balance | ±0.05mV/V |
| Non-linearity | ±0.2% R.O. |
| Hysteresis | ±0.2% R.O. |
| Non-repeatability | ±0.1% R.O. |
| Creep(10min) | ±0.1% R.O. |
| Safe overload | 150% F.S. |
| Ultimate overload | 200% F.S. |
| Compensated temperature | -10...+40oC |
| Operating temperature | -20...+60oC |
| Temperature shift zero | ±0.02% R.O./oC |
| Temperature shift span | ±0.02% R.O./oC |
| Input resistance | 350±30 ohms |
| Output resistance | 350±10 ohms |
| Insulation resistance | >2000M ohms |
| Ingress protection | IP40 |
| Material of element | Stainless steel |
| Cable | Ø5*3000mm 4-core shielded |
| Wiring code | Clockwise@ |
A torque sensor is a transducer that converts a torsional mechanial
input into an electrical output signal.Rotary torque sensor is
designed to measure rotating torque like motor torque ,
rotating shaft torque, mixture torque, etc.. Dynamic torque
transducer can also be used to measure static torque(which is also
known as reaction torque).The output range of rotary torque sensor FY01 is normally within -25mV...+25mV, signal amplification may be
required for most applications, a signal conditioner can be used to
convert mV signal into -5~5V, 0-10V or 4-20mA output for easy
data processing.Taking torque cell FY01-100NM and amplifier
FSC(-10-10V)-24V for example,the torque-voltage relationship will
be 0-100NM in CW direction VS 0-10V output, 0-100N*m in CCW
direction VS 0-(-10V) output, 1V output corresponds to 10Nm torque
in clockwise direction, -5V output corresponds to 50N-m torque in
anticlockwise direction, and so on.
