Henan Zhengzhou Mining Machinery CO.Ltd |
Verified Suppliers
|
|
Vertical Kiln / High Production Lime Vertical Kiln with 50-500(t/d)
Vertical Shaft Kiln Introduction:
Lime vertical kiln, just like itsname, the shape is erect. It is used for calcination limestone. Due to has lowenergy consumption, less cover area, less investment, wide applicability fuel,and more advantages, it was widely used in metallurgy, construction materials,calcium carbide, Nanometer calcium carbonate, aerated concrete, sugaring, etc.The vertical kiln was manufactured by ZK group with modern new technology, whichis an environment protection, save energy, higher machanization andautomaticity, quite modern lime kiln. Because it adopts the modern technology,make full use the cheap energy, especially pollution of gas for environmentharmful( such as conventer gas, blast furnace gas, calcium carbide furnace tailgas) as the energy, turn waste into wealth. Thus will protect the environment,and produce the high quality lime with lowest cost. To use this new technologyenterprise, economic benefits have increased significantly.
The Special and Main Equipment for the Kiln as Follows:
1. Limestone batching electric weighing system
2. Intelligent master controller
3. Rotary distributing devices
4. Intelligent detection of material level gage
5. Simulation hood
6. Pan discharging lime machine
7. Two section seal valve lime discharging machine
Our Advantages:
1. Save energy;There are preheatingzone, calcination zone, cooling
zone from the top to bottom of kiln inside. Thecooling air blow
into the cooling zone from the bottom, though the heattransfer, the
goods were cold, and the cooling air was heated, then put intothe
calcination zone with the heat for burning, thus reduce the
energyconsumption. The flue gas from the fuel after calcination
enter into thepreheating, make the material heat to
pre-dissociation temperature. The fluetemperature fall to 170-300℃,
thencome out from the kiln.
2. The shell of kiln use four layerrefractory in vertical masonry,
good effect of thermal insulation, thetemperature of shell will be
controlled higher 60℃ than environment, save energy remarkably.
3. Long service life of refractory,the material not directly crash
the work surface of refractory, but itsfraction with work surface
by gravity setting. Thus it greatly reduces the wearrate of
refractory, the refractory will be used in 6-10 years in normally.
4. Less cover area, because thevertical kiln in vertical layout,
feeding use the single bucket elevator inhigh angle layout, each
functional area is decorated compact, greatly reducesthe cover
area.
Technical Parameters:
Technical Parameters of Lime Rotary Klin | |||||
Size | Capacity(t/d) | No. of Supporter | Reducer | Motor | Power (kW) |
Ø2.2×38m | 120 | 3sets | ZS125-5 | YVF2-225M-4 | 45 |
Ø2.5×40m | 150 | 3sets | ZS145-5 | YVF2-250M-4 | 55 |
Ø2.8×43m | 200 | 3sets | ZS165-6 | YVF2-280S-4 | 75 |
Ø3.0×50m | 230 | 3sets | ZS165-3 | YVF2-280M-4 | 90 |
Ø3.2×50m | 250 | 3sets | ZL130-16 | YVF2-315L2-6 | 132 |
Ø3.6×55m | 400 | 3sets | ZSY560-63 | YVF2-355M1-6 | 160 |
Ø3.8×58m | 500 | 3sets | ZSY560-63 | YVF2-355M2-6 | 185 |
Ø4.0×60m | 600 | 3sets | ZSY630-35.5 | YVF2-355M4-6 | 200 |
Ø4.3×64m | 800 | 3sets | ZSY630-35.5 | YVF2-355L3-6 | 250 |