Active Member
|
[China]
Address: 18F, Building 2, Nantai Yunchuanggu, Phoenix Community, Guangming District, Shenzhen, Guangdong, China
Contact name:Amy
Shenzhen FRIDA LCD Co., Ltd |
|
|
13.3 Inch Tft Display 1920x1080 Ips Viewing Angle Edp Interface 30 Pins
General Description:
1.2 lane eDP interface with 2.7Gbps link rates
2.Thin and light weight
3.16.7M (8bit) color depth, color gamut 100%DCI-P3 ( CIE1931 )
4.Data enable signal mode
5.Side mounting frame
6.Green product (RoHS & Halogen free product)
7.Low driving voltage and low power consumption
8.On board EDID chip
Specifications:
| Parameter | Specification | Unit |
| Active area | 293.76(H) ×165.24 (V) | mm |
| Number of pixels | 1920 (H) ×1080 (V) | pixels |
| Pixel pitch | 51 x 153 | um |
| Pixel arrangement | RGB Vertical stripe | |
| Display colors | 16.7M (8bit) | |
| Color gamut | DCI-P3 100% Typ,95%Min | |
| Display mode | Normally Black | |
| Dimensional outline | 298.76 ±0.3(H)*181.33 ±0.5(V) (W/PCB)*2.377(Max) | mm |
| Weight | 172.2(max) | g |
| Surface treatment | HC | |
| Surface hardness | 3H | |
| Back-light | Lower Down side, 1-LED Lighting Bar type | |
Power consumption
| PD: 0.39(Max) | W |
| PBL: 3.5(Max) | W | |
| PTotal : 3.89(Max) | W |
Absolute Maximum Ratings:
| Parameter | Symbol | Min. | Max. | Unit |
| Supply Voltage | VDD | -0.3 | 4.0 | V |
| eDP input Voltage | VeDP | 0 | 2.0 | V |
| Logic Supply Voltage | VIN | VSS-0.3 | VDD+0.3 | V |
| Operating Temperature | TOP | 0 | +50 | °C |
| Storage Temperature | TST | -20 | +60 | °C |
Electrical Specifications:
| Parameter | Min. | Typ. | Max. | Unit | ||
| Power Supply Voltage | VDD | 390 | 3.3 | 3.6 | V | |
Permissible Input Ripple Voltage | VRF | - | - | 300 | mV | |
| Power Supply Inrush Current | Inrush | - | - | 2 | A | |
Power Supply Current | Mosaic | IDD
| - | - | 119 | mA |
| RGB | - | - | 119 | mA | ||
Power Consumption | Mosaic | PM | - | - | 0.39 | W |
| RGB | PRGB | - | - | 0.39 | W | |
| BLU | PBL | - | - | 3.5 | W | |
| Total | PTotal | - | - | 3.89 | W | |
Interface Connection:
| Terminal | Symbol | Functions |
| Pin No. | Symbol | Description |
| 1 | GND | Ground |
| 2 | Lane1_N | eDP RX channel 1 negative |
| 3 | Lane1_P | eDP RX channel 1 positive |
| 4 | GND | Ground |
| 5 | Lane0_N | eDP RX channel 0 negative |
| 6 | Lane0_P | eDP RX channel 0 positive |
| 7 | GND | Ground |
| 8 | AUX_CH_P | eDP AUX CH positive |
| 9 | AUX_CH_N | eDP AUX CH negative |
| 10 | GND | Ground |
| 11 | LCD_VCC | Power Supply, 3.3V (typ.) |
| 12 | LCD_VCC | Power Supply, 3.3V (typ.) |
| 13 | BIST | Self Test |
| 14 | GND | Ground |
| 15 | GND | Ground |
| 16 | HPD | Hot plug detect output |
| 17 | NC | No Connection |
| 18 | NC | No Connection |
| 19 | FB1 | LED Current Feedback |
| 20 | FB2 | LED Current Feedback |
| 21 | FB3 | LED Current Feedback |
| 22 | FB4 | LED Current Feedback |
| 23 | FB5 | LED Current Feedback |
| 24 | FB6 | LED Current Feedback |
| 25 | NC | No Connection |
| 26 | NC | No Connection |
| 27 | VLED | LED Power Supply |
| 28 | VLED | LED Power Supply |
| 29 | VLED | LED Power Supply |
| 30 | VLED | LED Power Supply |
Optical Specification:
| Parameter | Symbol | Condition | Min. | Typ. | Max. | Unit | |
Viewing Angle Range | Horizontal | Θ3 |
CR > 10 | 80 | 85 | - | Deg. |
| Θ9 | 80 | 85 | - | Deg. | |||
| Vertical | Θ12 | 80 | 85 | - | Deg. | ||
Θ6 | 80 | 85 | - | Deg. | |||
| Luminance Contrast Ratio | CR | Θ = 0° | 800 | 1000 | - | ||
| Luminance of White | center | Yw |
Θ = 0° ILED = 19.7mA | 312 | 390 | 468 | cd/m2 |
| White Luminance Uniformity | 5 Points | ΔY5 | - | - | - | % | |
| 13 Points | ΔY13 | 70% | - | - | % | ||
White Chromaticity | CCT | Θ = 0° | 6300 | 6800 | 7500 | ||
| MPCD | -5 | 10 | 25 | ||||
Reproduction of Color | Red | Rx |
Θ = 0°
|
Typ.-0.03 | 0.680 |
Typ.+0.03 | |
| Ry | 0.318 | ||||||
| Green | Gx | 0.256 | |||||
Gy | 0.703 | ||||||
| Blue | Bx | 0.151 | |||||
By | 0.046 | ||||||
| Color Gamut | DCI-P3 | 95 | 100 | - | % | ||
| Response Time(Rising+Falling) | TRT | Ta= 25℃Θ=0° | - | 60 | - | ms | |
| Cross Talk | CT | Θ = 0° | - | - | 2.0 | % | |
Handling Precautions:
1.As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning.
2.When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged.
