|
[China]
Trade Verify
Address: 608, Building B, Yinyi Duhui Guoji, No.8, Lane 559, Youngor Avenue, Haishu District, Ningbo, China
Contact name:Brandon Bao
Ningbo Brando Hardware Co., Ltd |
|
Verified Suppliers
|
|
|
Mini Pneumatic Piston Air Cylinder 25 Bore 50 Stroke Stainless Steel
In many industries, creation of a linear motion during an operation sequence is often required. A pneumatic cylinder, which is also referred to as an air cylinder, is one of the simplest, most cost-efficient solutions. Pneumatic cylinders are mechanical devices that convert the energy of compressed air to a linear motion.
Single-acting cylinders
Single-acting cylinders (SAC) use the pressure imparted by
compressed air to create a driving force in one direction (usually
out), and a spring to return to the "home" position. More often
than not, this type of cylinder has limited extension due to the
space the compressed spring takes up. Another downside to SACs is
that part of the force produced by the cylinder is lost as it tries
to push against the spring.
Double-acting cylinders
Double-acting cylinders (DAC) use the force of air to move in both
extend and retract strokes. They have two ports to allow air in,
one for outstroke and one for instroke. Stroke length for this
design is not limited, however, the piston rod is more vulnerable
to buckling and bending. Additional calculations should be
performed as well.
Specifications of MA Series Pneumatic Cylinder:
| Bore Size (mm) | 16 | 20 | 25 | 32 | 40 | 50 | 63 | ||
| Acting Type | MSA / MTA | Single Acting | - | ||||||
| MA / MAD / MAJ | Double Acting | - | |||||||
| MAR | - | Double Acting | |||||||
| MAC / MACD / MACJ | Double Acting with cushion | ||||||||
| Fluid | Air (to be filtered by 40μm filter element) | ||||||||
| Operating Pressure Range | Double Acting | 0.15 to 1.0 MPa (1.5 to 10.0 bar) (22 to 145 psi) | |||||||
| Single Acting | 0.2 to 1.0 MPa (2.0 to 10.0 bar) (28 to 145 psi) | ||||||||
| Proof Pressure | 1.5 MPa (15 bar) (215 psi) | ||||||||
| Temprature (℃) | -20 to +70 | ||||||||
| Speed Range (mm/s) | Double Acting: 30 to 800, Single Acting: 50 to 800 | ||||||||
| Cushion Type | MAC / MACD / MACJ Series: Variable cushion; Other Series: Bumper | ||||||||
| Port Size | M5x0.8 | 1/8'' | 1/4'' | ||||||
Stroke of MA Series Pneumatic Cylinder:
Symbol of MA Series Pneumatic Cylinder:
Ordering Code of MA Series Pneumatic Cylinder:
Criteria for selection: Cylinder thrust:
Installation & Usage:
1. When load changes in the work, the cylinder with abundant
output capacity shall be ed.
2. Relative cylinder with high temperature resistance or corrosion
resistance shall be chosen under the condition of high temperature
or corrosion.
3. Necessary protection measure shall be taken in the
environment with higher humidity, much dust or water drops, oil
dust and welding dregs.
4. Dirty substances in the pipe must be eliminated before cylinder
is connected with pipeline to prevent the entrance of particles
into the cylinder.
5. The medium used by cylinder shall be filtered to 40μm or below.
6. Anti-freezing measure shall be adopted under low temperature
environment to prevent moisture freezing.
7. The cylinder shall be carried out test run without load before
application. Prior to run, buffer shall be turned to the minimum
and gradually released to avoid the damage on cylinder caused by
excessive impact.
8. The cylinder shall avoid the influence of side load in operation
to maintain the normal work of cylinder and extend the service
life.
9. If the cylinder is dismantled and stored for a long time, please
conduct anti-rust treatment to the surface. Anti-dust caps shall be
added in air inlet and outlet ports.
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
Welcome to your any question and inquiry!
