Active Member
|
[China]
Address: Longgang Shenzhen City, China
Contact name:Sherry
Shenzhen Maixiang Technology Co.,Ltd |
|
|
24V DC Servo Motor Barrier LED Arm Barrier Parking Gate Fast Speed
Functions and Features:
1. Gate automatically open when power off, no clutch design, no
need human intervention. When power on,
gate automatically reset, restore to the gate closing state, truly
unattended, fire safety standards. If special
requirement, manual operation is required when power off, operating
arm open and close manually also can
be realized by setting up control board DIP switch, which ensure
that the system can be used at any time.
2. The use of Single Compression Balance Spring device, good
regulation, no noise, indefatigable, not easy to break, safe and
reliable.
3. A variety of input and output modes can be selected, normally
open normally closed are optional.
4. Arm opening angle can be adjusted from 60 to 90 degrees, 10
degrees resolution, suitable for eaves prominent place to install.
5. Closing speed can be adjusted.
6. Barrier gate up &down signal relay switch output.
7. Barrier gate running state: OK signal output indicating that the
gate is working properly.
8. Barrier gate operation abnormal alarm signal output.
9. R&G Traffic light relay switch signal output.
10. External loop detector signal anti-smashing interface, infrared
sensor signal anti-smashing interface.
11. Count mode interface.
12. Arm Open priority anti-smashing function. No matter the current
gate in what state, the operator through the triple
push button, software or remote control to issue an open command,
the gate will give priority to the implementation of the opening
action.
13. Barrier with anti-collision protection function, when the
vehicle hits the gate arm, arm can be swing out to avoid
damage to the vehicle, and barrier gate machine.
14. Delay closed selection function.
15. High-sensitivity arm auto reverse function (intensity can be
adjusted).
16. Parking system interface.
17.RS485 or RS232 network communication control up &down
interface (no need to install communication module)
18. Anti-collision alarm signal interface.
19. Adjustable speed port (from 0.9s to 10 s)
20. High-strength precision cast steel, industry moving parts
beyond the industry quality
MX controller specifications:
| MX Controller | ||
| Voltage(±10%) | 100-240 volt | 100-240 volt |
| Frequency(Hz) | 50-60 | 50-60 |
| Max Power Consumption(watt) | 8 | 8 |
| Fuse | F5AH | F5AH |
| Control Voltage | 24V DC/max.3000mA | 24V DC/max.3000mA |
| Input-end Number | 8 | 8 |
| Open Collector Output Number | 2 | 2 |
| Zero Level Reversal Relay Number | 3 | 3 |
| Operating Temperature Range℃ | -45℃~+85℃ | -45℃~+85℃ |
| Protection System(IP) | 20 | 20 |
| Weight(gram) | 450gram | 450gram |
| Dimension | mm(L-W-H) | 158*126*55 |
Barrier gate specifications:
| MX-88 barrier gate | V06T | V09T |
| Max Boom Length and Diameter | 2500mm, Ф75mm | 3000mm, Ф75mm |
| Open/Close Time | 0.9sec,2.5sec,4.5sec | |
| Power Supply | 24/100/240VAC,50/60Hz | 24/100/240VAC,50/60Hz |
| Power Consumption | max.150W | 100w |
| Machine Case | Varnished 2.0mm steel plate | Varnished 2.0mm steel plate |
| Machine Case Size(W*D*H) | 342*312*959mm | 342*312*959mm |
| Net Weight | 43kg | 50kg |
| Operating Temperature Range℃ | -45℃~+85℃ | -45℃~+85℃ |
| Driving Method | Servo motor | Servo motor |
| Protection System(IP) | 65 | 65 |
| Insulation Class | F | F |
| Relative Humidity | ≤90% | ≤90% |
| Motor Speed | 3000r/min | 3000r/min |
| Remote Control Distance | ≤100m (open, sunny weather) | ≤100m (open, sunny weather) |
| Output Torque | 1.2N.M*140=160N.M | 0.86N.M*140=120N.M |
| Running Noise＜ | 45dB | 45dB |
| Surface Treatment | Outdoor metal powder electrostatic spraying | Outdoor metal powder electrostatic spraying |
Technical Support:
If the operational failure can’t be handled by your technical
staff, please contact our authorized service representative or
professional assistance.
Please provide the barrier gate model, product serial number,
version and other information when contact us for technical support
services, which you can find in barrier gate model plate.
Security Tips:
1 General Security Information
The design, manufacture and testing of the barrier system are use
of the "state-of-the-art" technology and can only be manufactured
after the satisfaction of the strict safety and reliability of
technical standards. Even so, if the barrier system is not properly
operated, it will also cause danger to people and property. So this
manual must be fully read and all of the safety information must be
followed.
If the barrier system is improperly used or used for non-intended
use, the
manufacturer will refuse to be responsible for the resulting
consequences and will cancel the original quality assurance.
2 Suggested Application
High-speed barrier gates can only be used for toll stations for
highways and trunk roads.
The medium barrier gates are designed to control the access roads,
multi-storey car parking lot and other vehicular access routes for
vehicle parking areas.
The controller is specifically designed to control the barrier
gates.
It is not permissible to use these barrier gates for any other
purpose.
Any changes and replacements to the barrier gates and the control
components are prohibited.
3 Safety sign
The following symbols used in this instruction are used to indicate
potential hazards and other safety information.
4 Operating Safety
A safety margin of at least 500 mm must be provided between the end
of barrier gates and the physical obstructions (such as buildings,
walls and fences, etc.) that are closest to it. When the boom is
moving, the personnel and other objects are forbidden to stay near
the barrier gate. If you have installed the barrier and operating
elements and are connected to a fixed main power supply, you must
use a full polarity with a safety device. It must be operated in
accordance with this installation manual, and be approved by the
company before making any changes. The locking device of the boom
is designed to bear winds of magnitude 10 (= 500N / ㎡.). If it’s
expected that there will be a higher speed wind, must be approved
by the company before change the fixed device of boom. A boom more
than 3.5meter will be required to install a swing support or a
support column. All of the circuit connections, wiring work and
replacement of any circuit components must be carried out by
professionally trained electricians. Please firstly disconnect the
connections with main power supply before opening barrier gates. It
is forbidden to make technical modification or changes to the
barrier system.
After cutting off the power, start at least 10 seconds before starting again.
5 Technology Development
The manufacturer reserves the right to modify the technical
specifications of the product to meet the latest technological
developments without prior notice. The company is glad to provide
the information about current operating manual and any information
about the changes and extensions.
FAQ:
Q: Are you trading company or manufacturer ?
A: We are a professional barrier gate manufacturer.
Q: How long is your delivery time?
A: Generally it is 2-5 days if the goods are in stock. or it is 5-7
days if the goods are not in stock, it is according
to quantity.We can send it for you by DHL/Fedex/TNT/SEA/AIR or your
requirments.
Q: How about payment terms our company provide?
A: T/T or Western Union.
Q: Do you provide free samples ?
A:No,we don't provide free samples. The MOQ of our products is
1pcs.
