Results forlcd metal conductivity testerfrom 21034 Products.
|
Condensation Tester Brief Introduction:test defrosting time and water evaporation after refrigerator’s freezer is turned off light Meet standard:meet requirements of GB4706.13...
|
|
|
|
Covering Scratch Tester Product details: The device is used to check abrasion strength of printed circuit boards scratches are made across five pairs of conducting parts and the ...
|
|
|
|
IEC 60950-1 clause 2.10.8.4 Automatic Abrasion Resistance Tester / Printed Circuit Abrasion Strength Device Application: The device is used to check abrasion strength of printed ...
|
|
|
|
Container Compression Tester Function Description Container Compression Tester is the most direct test equipment for testing carton and other packing containers’ compression ...
|
|
|
|
IEC62262 Mechanical Strength Tester On Sheet Metal / Pendulum Impact Test Apparatus For Energy Impact Test Product details: This testing device conforms to IEC62262. It is used for ...
|
|
|
|
Dielectric Strength Tester Items Model Description Standard Dielectric strength tester KP-DST pole diameter: 5 ± 0.1mm Metal club weight: 100 ± 2g Max measure rang: 20mm Max ...
|
|
|
|
Sulfide Dioxide Tester Function Description The sulfide dioxide fogger is applicable to accelerated corrosion tests on protective layer,parts,electronic components and industrial ...
|
|
|
|
Dielectric Strength Tester Items Model Description Standard Dielectric strength tester KP-DST pole diameter: 5 ± 0.1mm Metal club weight: 100 ± 2g Max measure rang: 20mm Max ...
|
|
|
|
Pressure Tester- IEC 60335-1-Annex B-B.20.1, 2070 kPa Pressure Tester 20 Stability and mechanical hazards B.20.1 The enclosure of a battery-operated appliance incorporating an ...
|
|
|
|
IEC 60335-2-25, 6th Edition (2010) - A1/2014 - A2/2015 Household and similar electrical appliances – Safety – Part 2-25: Particular requirements for microwave ovens, including ...
|
|
|
|
Limited short-circuit test , IEC 62368-1-Annex R R.3 Test method The source shall be applied to the EUT via the mains cord supplied or specified by the equipment manufacturer. ...
|
|
|
|
IEC 60335-2-120 Electronic cigarette battery enclosure tester Compliant with standards and clauses: IEC 60335-1: 2020-Appendix BB-20.1.,IEC 60335-2-120-Appendix B-20.1 Purpose of ...
|
|
|
|
IEC 62368-1 Annex G.8.2.2 Resistor loading box 1. IEC 62368-1, Annex G.8.2.2 2. Resistance: 3840ohm(60W), 1920ohm(120W),960ohm(240W),480ohm(480W),240ohm(960W),120ohm(1920),60ohm ...
|
|
|
|
Luminaire Adjustment Test Device Meet standards of GB/7000.1-2002 Chapter 4.14. And EN60598-1:2000 Function: Applied to testing adjustment device with soft cable and wire built in ...
|
|
|
|
ZR-1210model respirator resistance detector Product introduction Zr-1210 respirator resistance tester is used to measure the inspiratory and expiratory resistance of the mask under ...
|
|
|
|
IEC60884-1 figure 40 / VDE 0620 Bild 39 Abnormal Heat of Insulating Sleeves of Plug Pins Test Apparatus 1. Product information: To determine testing resistance to abnormal heat of ...
|
|
|
|
Cu90Ni10 Copper Alloy Tube , ASTM B111 C70600 O61 Annealed Seamless Heat Exchanger Tube The C70600 / Cu90Ni10 alloy tube primarily consists of approximately 90% copper (Cu) and 10% ...
|
|
|
|
ASME SB564 UNS N02200(Nickel 200) DIN2.4066 Stainless Steel WNRF Flange Nickel 200 is a 99.6% pure nickel alloy and one of the toughest metals in existence. It exhibits excellent ...
|
|
|
|
ASTM B111 C70600 O61 LOW FIN TUBE COPPER NICKEL ALLOY CUNI 90/10 Fin efficiency is defined as the ratio of actual heat flow of the fin to that which would be obtained with a fin of ...
|
|
|
|
ASTM A213 Gr.T5 Stainless Steel Seamless Tubes For Oil Gas Heat Exchangers Chemical A213 T5 alloy steel tube is equivalent to domestic 1Cr5Mo alloy steel pipe, metal organization ...
|
|
|
You may also be interested in :