Forced Gas Boiler Hot Water Heater 2.1MW Fire Gasonline Hot Water Boiler

Forced hot water boiler Big Production Ability 2.1MW Fire Gasonline Hot Water Boiler

The Forced hot water boilerincludes an electric hot water boiler, a fuel hot water boiler, a gas hot water boiler, and a coal-fired hot water boiler. The hot water boiler is a boiler that produces hot water, and refers to heat energy or other heat energy (such as electric energy) released by combustion of the fuel. , solar energy, etc.) A thermal energy device that heats water to a rated temperature.

The Forced hot water boiler is divided into a normal pressure hot water boiler and a pressure hot water boiler. The atmospheric pressure hot water boiler belongs to a non-pressure civil life boiler, which is convenient, fast and safe to use, and does not need to be filed by the technical supervision department; the pressure hot water boiler is a pressure vessel. It belongs to special equipment. The design, manufacture, installation and use of pressure-bearing boilers are supervised by technical supervision departments and need to apply for boiler use certificates.

The Forced hot water boiler we usually refer to is an atmospheric hot water boiler. The atmospheric hot water boiler is not subject to conditions and there are no safety hazards. Nowadays, people choose heating, bathing and hot water for atmospheric hot water boilers.

Boiler and hot water heater requirements
The design, manufacture and inspection of the boiler shall comply with the requirements of the "Safety Technical Supervision Regulations for Hot Water Boilers".
The boiler should have modern technology, long-term operation output, less air leakage, high thermal efficiency, low water resistance, low power consumption, and low operating costs. The boiler and its supporting equipment should be brand new, reliable, technologically advanced and mature.
The boiler structure is reasonable and advanced, and can adapt to load changes. It should be able to run smoothly within the load range of 20% to 110%. The boiler has a fast heating rate, meets the requirements of fast start-stop, fast operation, convenient maintenance and stable performance.

Forced hot water boiler Technical performance requirements
1, Boiler body
1.The welds of the pipes of each heating surface of the boiler shall be subjected to 100% non-destructive inspection and shall have the inspection certificate. Strict inspection should be carried out before leaving the factory, and no foreign matter or welding slag is allowed to remain in the pipe and in the header.
2.The design and manufacture of each component must comply with the regulations issued by the state. Welding of dissimilar steels with large differences in alloying elements in the heating surface of the boiler should generally be completed in the manufacturing plant and should have welding records (including pre-weld preheating, welding methods, joint types, welding rods, post-weld heat treatment, etc.). ).

2,Water supply tank: The boiler should be provided with automatic water supply function. And the water tank should be equipped with a water tank cover. The tank should be installed with an overflow pipe in a location with drainage. After the water tank is installed, clean up the debris in the water tank.

3,Points, water collectors
The effective length of the water separator and the water collector shall not be less than 800 mm, and φ shall not be less than 219 mm.

4, Chimney
Diameter: D219, length: 6 meters. Low temperature discharge is required, and the exhaust gas temperature does not exceed 200 degrees.

5,Electrical and Control
1.The bidder shall provide the boiler electrical control cabinet, including various electrical components and electrical wiring devices, in the factory as required by this specification. The electric wiring device and the electric motor control and protection equipment of the electric control cabinet shall be provided in complete. The selection of electrical components of the electric control cabinet should be advanced and reliable. An alternate fuse must be provided.
2.The electronic control system should have two sets of systems; one is for the automatic system to operate separately, and the other is for manual system operation, any type of damage can not affect the other normal use.

Commerical hot water boiler Features:
1. Adopting the normal pressure mode, the boiler is not under pressure, and the safety factor is high, and there is no danger of explosion.
2. Designed as a burner-type pyrotechnic tube boiler, the fuel is burned by the burner in a micro-positive pressure in the furnace, the high-temperature flue gas is radiated and heat-exchanged in the furnace, and then enters the convective heat exchange of the pyrotechnic tube, and finally passes through the upper cigarette case. discharge.
3. The boiler body design of the boiler body adopts computer optimized simulation design, which fully optimizes the size of the boiler and makes the shape harmonious and beautiful.
4. The flue pipe is inserted with a baffle to slow down the flue gas discharge speed, strengthen the heat exchange, ensure the heat generated by the fuel combustion to heat the boiler water to the greatest extent, and greatly improve the thermal efficiency of the boiler.
5, equipped with imported brand burners, fully automatic program control, high degree of automation, the fuel system provides the fuel needed for combustion, the air supply system sends the appropriate wind speed, air volume, the ignition system ignites the mixture of air and fuel, the detection system Ensure stable and safe combustion of the burner
6. The gap between the large diameter pipe and the large hole bridge makes the scale coating thin and easy to clean in the same time. Product map
7, the shell shell furnace large interlayer water jacket, the boiler water capacity is large, can provide sufficient boiling water.
8, with multiple safety protection: leakage protection means that leakage automatically cuts off the power supply; overheat protection means that when the boiler water temperature reaches the alarm temperature, the burner is automatically stopped and an alarm is issued; when the secondary overheat protection means that the temperature of the boiler casing exceeds 105 °C, it is automatically cut off. The secondary circuit, the boiler stops working; the water level detection protection uses the sophisticated water level electrode rod to monitor the water level in real time, and the water level is lower than the upper limit water level solenoid valve until the upper limit water level is reached.
9, mechatronics design, small size, easy to install and transport.
10. The furnace is specially treated to ensure the water quality is clean and hygienic.
11, the outer lining aluminum foil glass wool for insulation, better insulation effect.
12, white color plate packaging, beautiful, clean and rust resistant.
13. The water supply port is at the lower part, the solenoid valve automatically replenishes water, and the boiling water in the boiling water area takes water to eliminate the phenomenon of “hot and cold water” and “thousand boiling water” to ensure that 100% of the drinking water is pure boiling water. 14. The boiler can be used in two machines, which can supply boiling water and provide hot water.

Oil water boiler 0.35MW-14MW Oil Gas Fired hot water boiler technical datasheet

Oil water boiler Vocume hot water boiler