Active Member
|
[China]
Address: No.27 Yinghu Road, Wangting Town, Xiangcheng District, Suzhou City, China
Contact name:
Suzhou Hengxie Machinery Co., Ltd |
|
|
HXE-450/13DL Big Copper wire drawing machine
I. Application
HXE-450/13DL Big
Copper wire drawing machine is used to draw single bare copper wire
from 8mm to 1.2mm-4.5mm.The drawing capstans are arranged in a line
that are able to work continuously with drawing speed and
electrical control can be matched with each other.
II. Componenets of equipment
| Name | Quantity |
| 1. Cantilever Pay-off shelf | 1 |
| 2. HXE-450/13DL Main drawing machine | 1 |
| 4. HXE-180 Tension controller | 1 |
| 6. HXE-SX630 Double spoolers | 1 |
| 7. Electrical cabinet | 1 |
| 8. Operation panel / With PLC&Touching screen | 1 |
III. Main technical parameters
| 1. Inlet | 8mm |
| 2. Outlet | 1.2mm-4.0mm |
| 3. Diameter of capstans | 450mm |
| 4. Speed | 1500m/min, Capacity say 1.2mm, 780kg per hour |
| 5. Slip ratio | 1.4-1.2 decrease |
| 6. Quantity of capstan | 13 |
| 7. Capstan | Tungsten carbide (With wire threading function) |
| 8. Quick dies change | Available / Require less dies |
| 9. Main motor | DC280KW, with DC Controller |
| 10. Fix speed motor | DC75KW, with DC Controller |
| 11. Gear | Changeable |
| 12. Noises of machine | ≤85 db |
| 13. Protection cover | Motor transmission cover installed |
| 14. Others | Heat exchanger for Gear oil is provided |
| 15. Others | All main pipes are provided |
| 16. Others Gear oil station system is provided, including: Pump, Gear oil tank, Pipes, Oil Pressure Gauge, Signal wire. | |
| 17. Others Heat exchanger for Lubrication oil and Heat exchanger for cooling water, no need. You need prepare one Underground Tank for Lubrication Oil recycle, one Water Tower for Cooling Water recycle. | |
IV. After sale service
Warranty: after shipping, machine part one
year, electrical parts six months
Under these situation mentioned, the Seller will not take
responsibility, but if the Buyer agree, will charge fees
accordingly to repair the machine.
A. Due to wrong operation while shipping.
B. Due to Buyer`s wrong preparation that may cause damage to the
machine.
C. Due to Buyer`s wrong operation that may cause damage to the
machine.
D. Not in the consuming part list.
E. After agreement are made for the shipping, for any damage, Buyer
should inform Seller in letter form to repair in seven days, If
beyond the dare, Seller shall take no responsibility.
F. For any other failures due to acts of God (such as lightning,
typhoon, earthquake, riots, war, fire or flood) and other factors
that will cause damage, Seller shall take no responsibility.
G. Seller guarantee provide long term support regarding the parts
and teach. After warranty, will charge accordingly.
V. Operating procedures
5-1. Open power switch
5-2. According to the wire diameter, choose the dies (Check the die list).
5-3. Use pliers to break the wire to get a smaller section.
5-4. Use pliers to make the wire through the dies, then pull the wire out (Use foot switch to make the machine running in a low speed to make the wire move).
5-5. Wire direction, please check the Drawing for Wire path.
5-6. After make the wire through all the parts, close the annealing door and the spooling door, make the tension swing arm in the lowest position. and in running, the balance arm should be in the horizontal line. No big shake, no up and down frequently.
5-7. Open the Annealing switch, open the Pump, open and adjust the Drawing lubrication oil, Cooling water, Steam, Compressed air.
5-8. Set the length meters, then press the Start button to start the machine.
