0.2mm-0.6mm Output Vertical Type Fine Copper Wire Drawing And Annealing Machine

HXE-22DT Fine copper wire drawing machine with annealer

I. Main Technical parameters

1. Usage single bare copper wire drawing and annealing, Inlet size 1.6mm, Outlet size 0.2mm-0.6mm

Machine speed/max 1500m/min, Die number 22, Dies size 25mm×8-10mmT, Slip ratio 15.5%+10%

Wire drawing mode standing-mode and 4 axes.

2. Drive by Inverter control, Brand Inovance, Most widely used brand in drawing machine. Main motor 15KW, Spooler motor 3.7KW, China best brand. Annealing voltage DC60V/max, Annealing current DC500A/max, Annealing power 30KVA.

3. Annealing method DC Three section annealing, Annealing protection will be done by steam protection

Capacity of compressed air 0.4-0.6Mpa, 20L/min. Demand Water quantity for annealing and coolant 200L/min, Machine frame welded by steel plate.

4. Transmission Flat belts. Capstan Ceramic plasma. Lubricating system Pipe Spray, Bobbin size 300mm, loading capacity: 50kg/max. Bobbin loading & unloading type shaft type. Traversing unit 110W synchros motor, width: 270mm/max.

5. Tension control by Air pressure tension control (With Weight balance as Backup) , Cabinet 0.8m*0.6m*2.0m. Machine dimension 2.3m*1.6m*1.9m; Installation Area 3.3m*1.7m+0.8*0.6m, Machine weight 3400KG, Cabinet weight 500KG. In total for shipping around 4,000KG.

II. Usage

  HXE-22DT Fine copper wire drawing machine with annealer.

  It is used to draw and anneal single bare copper wire from 0.6mm-1.2mm to 0.1mm-0.32mm. 
 
III. Components
 

IV. The structure and principle of the machine

4-1. The annealing part, is three-section annealing, consist of Preheating section, annealing section and drying section. The fix speed capstan of drawing, the annealing capstans, are driven by the same motor, through belts, so the speed of drawing, speed of annealing, is the same, make sure no wire break.

4-2. The annealing capstans, are access to positive and negative power, make the wire pass through the annealing capstans with current, by short-circuiting, to preheat, anneal and dry.

4-3. The annealing current and voltage, by auto tracking the drawing speed to auto adjust.

4-4. To cooling fast to achieve the annealing, the annealing capstan is under the cooling water. There is a cooling tank at the bottom of the machine, cooling water, better use fat content of 0.5% emulsion. The

pump shall pump the cooling water through the pipe and the switch to the annealing door. Adjust the cooling water switch to make sure the water is in certain height.

4-5. To make sure the wire while annealing, no Oxidation, there is a steam-in protection pipe, connect the pipe to the Steam generator, to use the steam to protect the wire from the oxidation.

4-6. In the exit of the drying section, there is a blowing device. In the device, shall have two dies. Connect the air compressor to the air compress input pipe, then out by the blowing device, adjust the switch, to make all the left water of the drying part, on the surface of the wire, blow away.

V. Electric control

5-1. Electric components: Check Components list

5-2. Power source: 380V 50Hz(can be customized)

5-3. Indication

Power switch, Power indicator, On, Off

Digital line speedometer, Meter counter, Annealing current, Annealing voltage

Speed adjust, Annealing adjust, Fault indicator, Fault reset

Water pump switch, Annealing switch

Pressure gauge, Pressure adjust, Length reset, Emergency stop

Meter setting (Once reach the setting meters, machine will auto stop)

VI. Advantage and after-self service
 
A: Advantage
 
(1). HENGXIE has some world famous parts suppliers, has special lubrication system for the gears and bearing.
(2). Body and other key components and parts are produced by our own factory , quality is reliable.
(3). Our company’s developing process in more than 10 years.
(4). DC. three-section annealing
 
B: After-self service
 
Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.
 
     Under these situation mentioned, the Seller will not take responsibility, but if the Buyer agree, will charge fees accordingly to repair the machine.

1. Due to wrong operation while shipping.
2. Due to Buyer`s wrong preparation that may cause damage to the machine.
3. Due to Buyer`s wrong operation that may cause damage to the machine.

4. Not in the consuming part list.
5. After agreement are made for the shipping, for any damage, Buyer should inform Seller in letter form to repair in seven days, If beyond the dare, Seller shall take no responsibility.
6. For any other failures due to acts of God (such as lightning, typhoon, earthquake, riots, war, fire or flood) and other factors that will cause damage, Seller shall take no responsibility.

7. Seller guarantee provide long term support regarding the parts and teach. After warranty, will charge accordingly.