Active Member
|
[China]
Address: No.27 Yinghu Road, Wangting Town, Xiangcheng District, Suzhou City, China
Contact name:
Suzhou Hengxie Machinery Co., Ltd |
|
|
HXE-22DT Fine copper wire drawing machine with annealer
I. Usage
HXE-22DT Fine copper wire drawing machine with annealer is
used to draw and anneal single bare copper wire from 1.6mm to
0.2mm-0.6mm.
II. Main Technical parameters
1. Usage single bare copper wire drawing and annealing
2. Inlet size 1.6mm
3. Outlet size 0.2mm-0.6mm
4. Machine speed/max 1500m/min
5. Die number 22, Dies size 25mm×8-10mmT, Slip ratio 15.5%+10%
6. Wire drawing mode standing-mode and 4axes
7. Drive by Inverter control, Brand Inovance, Most widely used brand in drawing machine
8. Main motor 15KW, Spooler motor 3.7KW, China best brand
9. Annealing voltage DC60V/max, Annealing current DC500A/max, Annealing power 30KVA
10. Annealing method DC Three section annealing
11. Annealing protection will be done by steam protection
12. Capacity of compressed air 0.4-0.6Mpa, 20L/min
13. Demand Water quantity for annealing and coolant 200L/min
14. Machine frame welded by steel plate
15. Transmission Flat belts
16. Capstan Ceramic plasma
17. Lubricating system Pipe Spray
18. Bobbin size 300mm, loading capacity: 50kg/max
19. Bobbin loading & unloading type shaft type
20. Traversing unit 110W synchros motor, width: 270mm/max
21. Tension control by Air pressure tension control (With Weight balance as Backup)
22. Cabinet 0.8m*0.6m*2.0m
23. Machine dimension 2.3m*1.6m*1.9m; Installation Area 3.3m*1.7m+0.8*0.6m
24. Machine weight 3400KG, Cabinet weight 500KG. In total for shipping around 4,000KG.
25. Siemens PLC Touch Screen
III. Components
| Name | Quantity |
| 1. Pay-off shelf | 1 set |
| 2. HXE-22DT Drawing&Annealing machine | 1 set |
| 3. Electrical control system | 1 set |
| 4. Bobbin loading&unloading system | 1 set |
| 5. Spare parts | As per list |
| 6. Steam generator | Under confirm |
| 7. Lubrication Tank and Pump | Under confirm |
IV. Preparation before working
4-1. Check all parts lubrication conditions,
4-2. Check drawing lubrication oil, cooling water, steam, air pressure.
4-3. After checking, connect to power, according to the Electrical drawing, use foot switch, to make the machine operating in low speed (under 4m/s), if no Abnormal, then can begin to work.
V. Main machine structure
1-1. Material Q235
1-2. Structure The machine frame is welded by steel plates, sand blasting, annealing and quenching to eliminate the inner stress, then further processed by exactitude milling machine.
2. Wire inlet
Inlet location Located on the left of machine, 6 bores.
3. Axes
3-1. Materials 45# steel
3-2. Precision HRC25-27, to eliminate inner stress, to improve the rigidity.
4. Transmission Flat belts
VI. Operating procedures
6-1. Open power switch
6-2. According to the wire diameter, choose the dies (Check the die list).
6-3. Use pliers to break the wire to get a smaller section.
6-4. Use pliers to make the wire through the dies, then pull the wire out (Use foot switch to make the machine running in a low speed to make the wire move).
6-5. Wire direction, please check the Drawing for Wire path.
6-6. After make the wire through all the parts, close the annealing door and the spooling door, make the tension swing arm in the lowest position. and in running, the balance arm should be in the horizontal line. No big shake, no up and down frequently.
6-7. Open the Annealing switch, open the Pump, open and adjust the Drawing lubrication oil, Cooling water, Steam, Compressed air.
6-8. Set the length meters, then press the Start button to start the machine.
