Results forcompatible m finger probesfrom 6414 Products.
|
IEC62368 Jointed Test Probe / Finger Length 80mm Diameter 12mm Standard: Conforms to IEC 62368-1:2018 clause 5.3.2, T.3 and Figure V.2, IEC61032 figure 2 test probe B,IEC950 ...
|
|
|
|
IEC62151 Figure 3 - Test Probe - Length 80mm Diameter 12mm - For Information Technology Equipment IEC62151 clause 4.2.2.1 Accessibility The equipment shall be so constructed that ...
|
|
|
|
IEC 60745-2-5 Test Probe a for Circular Saw Guard Test, diameter 12mm, length 50mm Standard: IEC 60745-2-5 : Particular requirements for circular saws, clause 19.101.2 and Figure ...
|
|
|
|
UL60950-1 Figure NAF2-3 Accessibility Wedge, Probe Tip Thickness 2mm Standard description(UL60950-1 clause F.4.4): For HOUSEHOLD / HOME OFFICE DOCUMENT SHREDDERS , a warning ...
|
|
|
|
IEC 60065 Test Probe D 1mm Diameter 100mm Length for HAZARDOUS LIVE TEST IEC60065 Clause 9.1 .4 TERMINALS The use of a single-pole plug or a bare wire to make connection with a ...
|
|
|
|
IEC60335-1 Clause 20.2 Test Probe With 50mm Circular Stop Face/ Finger Length 80mm Compliance is checked by inspection, by the test of 21.1 and by applying a force not exceeding 5 ...
|
|
|
|
Safety Test Probe 13 IEC61032 Fig. 9 Short Test Probe Pin Product information: This pin is intended to verify the protection against access to hazardous live parts in class 0 ...
|
|
|
|
Test Finger Probe B Product information: This is a precision test finger made in accordance with many standards like IEC 61032 figure 2, IEC60950 figure 2A,IEC60884,IEC60335,UL507...
|
|
|
|
Food Waste Probe 31 IEC61032 Figure 14 , Access Probe To Hazardous Mechanical Parts Product information: Food waste probe 31 confirms to IEC61032 figure 14 standard. It is used for ...
|
|
|
|
Probe for Fan Impellers UL standard Safety Test Probe Product details: It conforms to standard requirement of UL507 Fig 8.2(S2140). It is used for fan impellers and other moving ...
|
|
|
|
EN 50636-2-100 Figure 2 Adult Arm Probe EN 13683-2003 Figure 5 Product information: The adult arm probe conforms to EN 50636-2-100 figure 2 and EN13683-2003: 5.2.1.3 fig 5. It is ...
|
|
|
|
UL1278 Figure 8.4 Articulate Probe Test Probe B - Verify Accessibility of Live Parts Product information: An electrical part of a heater shall be so located or enclosed that ...
|
|
|
|
Diameter 50mm Test Probe A Made Of Stainless Steel And Nylon, Accord With IEC60529 IP1 Product introduction: This probe made of stainless steel and nylon, the sphere made of ...
|
|
|
|
IEC 60065 Test Probe C 2.5mm Diameter 100mm Length for HAZARDOUS LIVE TEST IEC60065-2014 Clause 9.1 .5 Pre-set controls If a hole giving access to pre-set controls is marked as ...
|
|
|
|
Length 100mm Diameter 1mm - Test Probe D With 1 N Force Scale Display IEC60529 The 1mm test rod meets IEC61032 figure 4 test probe D and EN Standards including IEC60529 for IP4 and ...
|
|
|
|
IEC 60745-2-5 Test Probe A With φ35*5 Stop Face For Circular Saws Test Test method: IEC60745-2-5 clause 19.101.2.2 The upper guard on the side opposite the motor need not ...
|
|
|
|
Length 100mm Diameter 1mm - Test Probe D With 1 N Force Scale Display IEC60529 This wire is a test device used to prevent the human body from touching dangerous parts. This tester ...
|
|
|
|
BS EN 13126 - 5 Figure A . 2 Jointed Test Finger For Windows Restrictor Safety Testing Product information: Test gauges for Windows Restrictor safety testing. 2 pieces a set, gauge ...
|
|
|
|
Test Finger Probe B HT-I02 Description: This probe is intended to verify the basic protection against access to hazardous parts. It is also used to verify the protection against ...
|
|
|
|
Scratched Pin Electric Safety Testing Probes Product information: The test pin is used to do the scratch resistant test of the electrical solid insulation surface. It conforms to ...
|
|
|
You may also be interested in :