|
[China]
Trade Verify
Address: 4F, Building 4, GuoLe Technology Park, LiRong RD, DaLang, LongHua Dist. Shenzhen, China
Contact name:Cherry Liu
ANC International Co., Limited |
|
Verified Suppliers
|
|
|
30m Cisco Fiber Sfp Transceiver SFP+ 10GBASE-T Transceiver Copper RJ45 Module
Description
SFP+ 10GBASE-T Transceiver Copper RJ45 Module Reach 30m Cisco Compatible manufactured by ANC International Co., Limited is specifically designed for high speed communication links that require 10 Gigabit Ethernet over Cat 6a/7 cable with a link limit of 30 m. It is the first 10G copper SFP RJ45 module that offers 10Gb/s communication over Ethernet copper cables. In addition, this 10Gbase-T RJ45 SFP transceiver is compliant with SFF-8431 and SFF-8432 MSA. The power usage and heat generated for 10GBASE-T is 4-8 watts, but 10GBASE-T SFP+ copper transceiver consumes 2.5 watts. Obviously, the specification of SFP+ 10gbase-t rj45 transceiver has been optimized to save more than 0.5 W per port when compared to an embedded 10GBASE-T RJ45 port for link distances up to 30m. These power savings can add-up in ToR, mid-row and end-of-row switch connectivity. Implemented as an SFP+ form factor, the new 10GBASE-T copper sfp transceiver is a power-optimized solution for lengths up to 30m. SFP+ 10GBASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3 . SFP+-10GBASE-T uses the SFP's RX_LOS pin for link indication. If pull up SFP's TX_DISABLE pin, PHY IC be reset. The SFP+-10GBASE-T has an input voltage range of 3.3 V +/- 5%.
Features
Supports Links up to 30m using Cat 6a/7 Cable
SFF-8431 and SFF-8432 MSA Compliant
Low Power Consumption (2.5W MAX @ 30m)
Fast Retrain EMI Cancellation Algorithm
Low EMI Emissions
Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T
Hot-pluggable SFP footprint
Compact RJ-45 connector assembly
RoHS compliant and lead-free
Single +3.3V power supply
10 Gigabit Ethernet over Cat 6a cable
Ambient Operating temperature: 0°C to +60°C
Applications
10GBASE-ER at 10.3125Gbps
10GBASE-EW at 9.953Gbps
Other optical links
Optical Characteristics
Low-Speed Signals
MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals
(see section VII, "Serial Communication Protocol"). Both MOD_DEF(1)
and MOD_DEF(2) must be pulled up to host_Vcc
| Low-Speed Signals, Electronic Characteristics | |||||
| Parameter | Symbol | Min | Max | unit | Notes/Conditions |
| SFP Output LOW | VOL | 0 | 0.5 | V | 4.7k to 10k pull-up to host_Vcc, measured at host side of connector |
| SFP Output HIGH | VOH | host_Vcc -0.5 | host_Vcc + 0.3 | V | 4.7k to 10k pull-up to host_Vcc, measured at host side of connector |
| SFP Input LOW | VIL | 0 | 0.8 | V | 4.7k to 10k pull-up to Vcc, measured at SFP side of connector |
| SFP Input HIGH | VIH | 2 | Vcc + 0.3 | V | 4.7k to 10k pull-up to Vcc, measured at SFP side of connector |
High-Speed Electrical Interface
All high-speed signals are AC-coupled internally
| High-Speed Electrical Interface, Transmission Line-SFP | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Line Frequency | fL | 125 | MHz | 5-level encoding, per IEEE 802.3 | ||
| Tx Output Impedance | Zout,TX | 100 | Ohm | Differential, for all frequencies between 1MHz and 125MHz | ||
| Rx Input Impedance | Zin,RX | 100 | Ohm | Differential, for all frequencies between 1MHz and 125MHz | ||
| High-Speed Electrical Interface, Host-SFP | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Single ended data input swing | Vinsing | 250 | 1200 | mV | Single ended | |
| Single ended data output swing | Voutsing | 350 | 800 | mV | Single ended | |
| Rise/Fall Time | Tr,Tf | 175 | psec | 20%-80% | ||
| Tx Input Impedance | Zin | 50 | Ohm | Single ended | ||
| Rx Output Impedance | Zout | 50 | Ohm | Single ended | ||
