Disposable Virus Sampling Tube
Structure Composition
This product consists of a swab and a tube containing a
preservation solution. Provided non-sterile. The material of the
sampling tube body is PP, the material of the cap is PE, the
material of the swab rod is ABS, and the material of the swab head
is nylon fleece.
Sampling Tube
- The sampling tube body is transparent, the surface is smooth and
flat, and the label is clear and complete.
- The pipe body has no stains, no obvious scratches, cracks, and the
pipe wall thickness is uniform, no obvious bending or deformation;
the cap and the pipe body are well matched, tightly screwed, and no
crooked cover phenomenon
Preservation Solution
- The liquid should be odorless, tasteless, free of particles or
impurities visible to the naked eye, and should not be turbid. It
is normal for bubbles or bubbles to appear during transportation
and use.
- The standard range of PH value is between 7.0-8.5
- The storage capacity
is:1ml,1.5ml,2ml,2.5ml,3ml,3.5ml,4ml,5ml,6ml,7ml,8ml,9ml,10ml,12ml,15ml,20ml,25ml,
Tolerance ±10%
Sampling Swab
- Sampling swabs should be clean, odorless and tasteless, and the tip
of the sampling hair should feel soft, and the surface should be
free of macular spots, impurities, and hair loss.
- When the breaking force and the moving speed of the fixture of the
connection firmness tester is 200mm/min, the pulling force of the
sampling swab head and one end of the connecting rod should not be
less than 2N
- When the test span is 6cm (the span should avoid the breaking
point), the plastic rod should be able to withstand the axial
static pressure of 5N for 15s without permanent deformation or
breaking.
- Fix the head of the sampling swab and apply vertical downward
pressure at 90°. The breaking force of the sampling swab's breaking
point should not be less than 2N.
- After the tube body equipped with the preservation solution is
matched with the cap, the tube body and cap will not be broken, and
the preservation solution should not leak.
- Product identification should be clear, intact, tidy and undamaged
Swab size
Unit: mm
| Swab length (L2) | Length of broken head (L1) | Maximum diameter of swab rod (D1) | Minimum diameter of swab rod (D2) | Length of swab head (L3) |
| 150±5 | Mouth swab | Throat swab | Nasal swab | Mouth swab | Throat swab | Nasal swab | Mouth swab | Throat swab | Nasal swab | 20±3 |
| 30±5 | 80±5 | 80±5 | 2.5±0.2 | 2.5±0.2 | 2.5±0.2 | 2.0±0.2 | 2.0±0.2 | 1.1±0.2 |
Intended Use
Suitable for sample collection, storage, transportation, etc. of
the nasal cavity and oropharynx
Applicable Departments
Fever Clinic, Emergency Department, Laboratory Department,
Infection Control Department
Usage Method
- Clean your hands before sampling, tear off the outer packaging of
the sampling swab, take the swab out, and be careful not to touch
the swab head.
- According to different sampling requirements, use a swab to sample
the corresponding part.
- Immediately after sampling, put the swab into the collection tube
containing the preservation solution to avoid contact with other
parts.
- Break off the wiper rod, discard the tail, and then tighten the
tube cap to complete the sampling.
- After sampling, the virus sampling management should be properly
placed, stored, and transported to the testing department for
testing within 1 week.
Matters Needing Attention
- Confirm that the outer packaging of the product is intact, check
the storage tube, and confirm that there is no leakage.
- This product is for one-time use and secondary use is prohibited.
- The process of collecting samples should be considered as a
potential risk of infection, and the operation and handling must
meet the requirements of relevant laws and regulations.
- After the product is used, it should be disposed of in accordance
with the relevant regulations of medical waste.
Important
- Make sure that the top of the sampling swab does not touch any
surface before sampling.
- There is a risk of choking, when the sampling swab is inserted into
the mouth, care should be taken.
- After the pathogenic bacteria specimens are collected, the
disposable sampling swab should be completely inserted into the
preservation solution to maximize the retention of the pathogenic
bacteria.
- The storage tubes and swabs after use should be disposed of in
accordance with the relevant medical waste disposal methods when
discarding
Company profile
Zhongxiu Science And Technology Co.,Ltd., is a high-tech enterprise
engaged in the research and development, production and operation
of in vitro diagnostic products. The in vitro diagnostic products
developed by the company cover POCT series, microbial series,
biochemical series and immune series reagents and supporting
instruments.
The company has always adhered to the core concept of "fast and
accurate, living up to life", committed to providing society with
excellent products and services, and contributing to the cause of
human health.
