|
[China]
Trade Verify
Address: No.48, Baihao Industrial Street, Houjie Town, Dongguan City, Guangdong Province, China
Contact name:Andy
DONGGUAN WIREMAC MACHINERY EQPT. CO., LTD. |
|
Verified Suppliers
|
|
|
Automatic CCA Wire Wet Drawing Machine HMI Intelligent 400V AC
Introduction
Recrystallization annealing is applied to alloys with solid phase transformation (recrystallization) during equilibrium heating and cooling. The annealing temperature is a temperature above or within the phase transformation temperature range of each alloy. Heating and cooling are slow. Alloys undergo phase transformation and recrystallization during heating and cooling, so it is called recrystallization annealing, which is often referred to as annealing.
This annealing method is widely used in steel. The recrystallization annealing process of steel is: slowly heat to 30 ~ 50 ℃ above AC3 (hypoeutectoid steel) or AC1 (eutectoid steel or hypereutectoid steel) for an appropriate time, and then slowly cool down. Pearlite (or pre eutectoid ferrite or cementite) is transformed into austenite (first phase transformation recrystallization) during heating and the opposite second phase transformation recrystallization during cooling to form pearlite (or pre eutectoid ferrite or cementite) with fine grain, thick lamella and uniform structure.
The annealing temperature above AC3 (hypoeutectoid steel) causes complete recrystallization of the steel, which is called complete annealing. The annealing temperature between AC1 and AC3 (hypoeutectoid steel) or between AC1 and ACM (hypereutectoid steel) causes partial recrystallization of the steel, which is called incomplete annealing. The former is mainly used for castings, forgings and Weldments of hypoeutectoid steel to eliminate structural defects (such as widmanstatten structure, banded structure, etc.) and make the structure thinner and more uniform, so as to improve the plasticity and toughness of steel parts. The latter is mainly used for forging and rolling of medium carbon, high carbon steel and low alloy structural steel.
If the cooling rate of the forged and rolled piece is high after forging and rolling, the pearlite formed is fine and the hardness is high; If the temperature of stopping forging and rolling is too low, there is still a large internal stress in the steel. At this time, incomplete annealing can be used instead of complete annealing to recrystallize pearlite and refine grain, reduce hardness, eliminate internal stress and improve machinability. In addition, spheroidizing annealing of hypereutectoid steel with annealing temperature between AC1 and ACM is also incomplete annealing.
Technical Parameters
| Machine Specs | ZL250A06 | ||||||
| Inlet wire range | 2.60 mm - 3.00 mm | ||||||
| Outlet wire range | 0.40 mm - 1.60 mm | ||||||
| Drawing die | 21 dies | ||||||
| Production speed | 1800 m/min, max | ||||||
| Anneal power | 85 KVA | ||||||
| Machine material | Stainless steel | ||||||
| Component brand | Schneider, Yaskawa, Siemens, Habasit | ||||||
| Motor of dual-reel take up | 11 KW x 2 (AC Motor) | ||||||
| Equipment size | L28 × W4.5 × H5.0 M | ||||||
| Equipment weight | 9000 kgs | ||||||
Note: For more details, please contact us. Thank you.
Details Picture
Download Center
Manual of Machine Purchase
Packing, Shipping, Quality & Service, FAQ etc.pdf
Our Company
Dongguan Wiremac Machinery Equipment Co., Ltd. Is located in Houjie Town, a famous historic town in China. Our company is a wire and cable equipment manufacturer integrating R&D, processing, assembly, commissioning and after-sales.
The company is committed to copper wire, copper clad steel, copper clad aluminum and other metal wire deep processing and research, with a variety of high quality machines: micro wire drawing machine, fine wire drawing machine, fine wire drawing machine with continuous annealing, medium fine wire drawing machine, intermediate wire drawing machine, intermediate RBD wire drawing machine and copper rod breakdown machine.
Our company provides a complete set of wire processing solutions for customers, but also customize and design non-standard special equipment according to the requirements of customers.
Our company upholds the spirit of “Honesty-based, Quality-based” enterprise, and continue to research and develop innovation and development, with professional skills and standardized pragmatic management, in line with the “High-quality and High-efficiency” business philosophy, from the overall planning, staff training, installation and commissioning, after-sales service, to provide customers with better and more satisfactory products and service.
Our Workshop
FAQ
1. Q: Are you manufacturer or trading company?
A: We are a manufacturer.
2. Q: What info you need before you make the proposal?
A: The input & output wire diameter, spool size, application, 3
phase voltage & frequency, annealing or not, and your other
requirement.
3. Q: How can I trust you and make a payment to you?
A: (1) We are an audited supplier by international SGS, with its
certificate. They approve that we are an original manufacturer and
meet their standard.
(2) We are a member of Made in China, who is always responsible for all customers.
(3) Please visit us and check our factory by video, and request necessary documents from us.
4. Q: I have no experience buying something abroad. What can I do?
A: We will guide and show you how to do the importation, you can
also seek help from your local agency.
5. Q: Do you provide installing and debugging overseas?
A: Overseas machine installation and worker training services are
available.
6. Q: Can you make the machine according to my design or prototype?
A: Yes, we have an experienced team for working out the most
suitable design and production plan for the machine that you are
going to book with us.
7. Q: How does your factory do regarding quality control?
A: There is zero tolerance to poor quality. Quality control
complies with SGS & ISO 9001. Every machine has to past testing
and trial running before it's packed for shipment.
8. Q: How can I trust you that machines pasted testing and trial
running before shipping?
A: 1) We record the testing videos for you, and every necessary
photos for you.
2) We welcome you to visit us and test machine by yourself in our
factory.
9. Q: What about our after-sale service?
A: We provide technical support on line as well as overseas
services by skillful technicians.
10. Q: What should I do if I just start a new business?
A: Contact us immediately, we provide free consultant pre-sales
service. Also we can help you with material purchase, worker
training, etc.
11. Q: Can I visit you factory to check machines on-site? What
Should I bring when I visit your factory?
A: We are manufacturer, and welcome customers to visit us. For
special product design, you are suggested to bring some samples,
you can test it with our machines on-site.
12. Q: Can I use my own logo?
A: No problem, please inform us.
