|
[China]
Trade Verify
Address: 701, Yongchang Building, Xicheng Industrial Zone, Xixiang, Bao'an District, Shenzhen, China 518126
Contact name:Sunny
Shenzhen Qianhai Lensen Technology Co., Ltd |
|
Verified Suppliers
|
|
|
LS-RDIO0202 wireless I/O module 2 digital inputs 2 relay output 2km wireless control
Introduction
LS-RDIO0202 Modbus RTU is a 1W I/O module, 2 isolated digital inputs, 2 isolated relay outputs, 1 RS485 (wireless RS485 customizes). Wireless control 2km-3km. Use for pump control, water level monitoring, motor, valve, light ON-OFF control.
Transparent I/O System, no programming required
Not need internet, no third party cell, no monthly fees
You have full control over your own carrier
Real time status feedback from the remote site
Fast installation and easy setup
Parameter:
Input: 2 isolated digital active inputs (passive input customize)
Output: 2 isolated relay passive contact outputs (active output customize), contact max load 5A@220V AC, 5A@30V DC.
Communication: RS485 (wireless RS485customize)
Protocol: Modbus RTU
Collocated with a wireless data module whose transmitting distance is about 2km-3km. The working frequency 433MHz (400-470MHz); RF power: 1W; Receiving sensitivity: -123dBm
Receiving current: <50mA; transmitting current: 600mA
Power supply: DC 9V-36V
Dimension: 115mm*90mm*40mm
Application:
Lighting Control Systems
Wireless Pump Control
Wireless Valve Actuation
Conveyor Control
Grain Augers
Engine Control
Tank Level Monitoring
PLC Activation
SCADA
LS-RDIO0202 Parameter
| Parameter | |
| Power output: | 600mW |
| Wireless technology: | Lora |
| Power supply: | 9V-30V (usually choose 24V DC or 12V DC) |
| Control distance: | 5km LOS |
| Baud rate: | 2400bps |
| Receiving sensibility: | -123dBm@1200bps, -118dbm(9600bps) |
| Networking | |
| Networking: | Point to point and point to multipoint |
| Protocol: | Modbus RTU protocol |
| Port Description | |
| Input: | 2 active inputs (passive customize), isolated |
| Output: | 2 passive relay outputs, isolated contact max load AC250V/5A,DC30V/5A (active outputs 0-5V customize) |
| Communication port | RS485 (wireless RS485 customize) |
| Current | |
| Transmit current: | <350mA |
| Receiving current: | <20mA |
| General | |
| Frequency: | 915MHz |
| Channel No: | 16 channels, can change via DIP switch |
| Physical Properties | |
| Dimension: | 115×90×40(mm) |
| Antenna Connector: | SMA,vehicle antenna with 1.5m cable |
| Temperature: | -35℃~+75℃( industrial) |
| Mounting method: | Standard 3.5 inch industrial guild rail |
LS-RDIO0404
Name: LS-RDIO0404 Wireless 4DI 4DO Modbus RTU Industrial ON-OFF control 2km RF ranges
Introduction
LS-RDIO0404 Modbus RTU is a 1W I/O module, 4 isolated digital inputs, 4 isolated relay outputs, 1 RS485(wireless RS485 customize). wireless control 2km-3km. Use for pump control, water level monitoring. Motor, valve, light ON-OFF control.
Transparent I/O System, no programming required
Not need internet, no third party cell, no monthly fees
You have full control over your own carrier
Real time status feedback from the remote site
Fast installation and easy setup
Parameter:
Input: 4 isolated digital active inputs (passive input customize)
Output: 4 isolated relay passive contact outputs (active output customize), contact load 5A@220V AC, 5A@30V DC.
Communication: RS485(wireless RS485customize)
Protocol: Modbus RTU
Collocated with a wireless data module whose transmitting distance is about 2km-3km; the working frequency 433MHz (400-470MHz); RF power: 1W; Receiving sensitivity: -123dBm
Receiving current: <50mA; transmitting current: 600mA
Power supply: DC 9V-36V
Dimension: 115mm*90mm*40mm
Application:
Lighting Control Systems
Wireless Pump Control
Wireless Valve Actuation
Conveyor Control
Grain Augers
Engine Control
Tank Level Monitoring
PLC Activation
SCADA
LS-RDIO0404 Parameter
| Parameter | |
| Power output: | 1W or 100mW version |
| Power supply: | 9V-30V (usually choose 24V DC or 12V DC) |
| Control distance: | 3km or (1km version) |
| Baud rate: | 2400bps default |
| Receiving sensibility: | -123dBm@1200bps, -118dbm(9600bps) |
| Networking | |
| Networking: | Point to point and point to multipoints |
| Port Description | |
| Input: | 4 digital active inputs(passive customize) |
| Output: | 4 relay outputs, contact max load AC250V/5A,DC30V/5A (active outputs 0-5V customize) |
| Communication port | RS485 (wireless RS485 customize) |
| Current | |
| Transmit current: | <600mA (or 100mA version) |
| Receiving current: | <50mA (or 20mA version) |
| General | |
| Frequency: | 433MHz, 450, 470 or other band |
| Channel No: | 16 channels,can change via DIP switch |
| Physical Properties | |
| Dimension: | 115×90×40(mm) |
| Antenna Connector: | SMA,vehicle antenna with 1.5m cable |
| Temperature: | 35℃~+75℃( industrial) |
| Mounting method: | Standard 3.5 inch industrial guild rail |
