1.90CBM Refrigeration Training Kit Heating And Air Conditioning Training Equipment 125W

ZM6151 Various Refrigeration And Air Conditioning Equipment Capacity Control / Faults System

1. Overview

* Practice-oriented model of a commercial refrigeration system1
* Refrigeration and freezing chamber to investigate different methods for capacity control1
* Simulation of 12 faults1
* 2 defrosting methods for freezing chamber

2. Technical Description

The efficient control of the capacity and temperature in refrigeration systems is an important topic in refrigeration technology. With different methods of capacity control can be investigated.

The components of a refrigeration circuit with refrigeration and freezing chambers are arranged clearly in the trainer. Solenoid valves enable the separate or parallel operation of the evaporators in the two chambers.

The circuit is equipped with a capacity controller, a start-up controller and
a combined pressures switch for the delivery and intake sides of the
compressor. One heat exchanger each in the inlet of the two evaporators
enables the supercooling of the refrigerant to be investigated for the
efficiency of the process. The refrigeration capacity of the two individual
chambers is controlled by a thermostat. The refrigeration chamber also
features an evaporation pressure controller.

There are two defrosting methods for the freezing chamber: an electric
defrost heater and a hot gas defrosting where hot refrigerant is fed directly from the compressor in the opposite direction through the evaporator.

The simulation of 12 different faults, such as e.g. faulty valves or clogged pipes, is activated using a touch panel PC.

Relevant measured values are transmitted directly to the touch panel PC and analysed. The software enables e.g. the representation of the cycle in the log p-h diagram.

The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.

3. Learning Objectives / Experiments

- familiarisation with the key devices for changing the refrigeration capacity
* thermostat

* capacity controller
* start-up controller
* evaporation pressure controller
* condensation pressure controller
- fault finding in refrigeration system components
- effect of refrigerant supercooling
- familiarisation with defrosting methods
* electric defrost heater
* hot gas defrosting
- representation of the thermodynamic cycle in the log p-h diagram

4. Specification

[1] investigation of a refrigeration system with refrigeration and freezing chambers
[2] refrigeration circuit with compressor, condenser, capacity controller, start-up controller, combined pressure switch and 2 evaporators in insulated chambers
[3] each chamber with solenoid valve, thermostat, thermostatic expansion valve, fan and heat exchanger for refrigerant supercooling
[4] refrigeration chamber with evaporation pressure controller
[5] freezing chamber with electric defrost heater and hot gas defrosting
[6] separate or parallel operation of the chambers via solenoid valves
[7] simulation of 12 faults
[8] touch panel PC for fault activation, data acquisition, evaluation and representation in the log p-h diagram
[9] refrigerant R404a

5. Technical Data

Compressor
- refrigeration capacity: 2440W at -10/30°C Condenser with fan
- volumetric air flow rate: 570m³/h Evaporator transfer areas
- refrigeration chamber: 1,12m²
- freezing chamber: 1,88m²
Electric defrost heater: approx. 125W
Capacity controller: 0,2...6bar
Start-up controller: 0,2...6bar
Thermostat: 2x -25...15°C
Evaporation pressure controller: 0...5,5bar
Measuring ranges
- temperature: 6x -50...50°C; 5x 0...100°C
- pressure: 3x -1...12,5bar; 2x -1...24bar
- flow rate: 2x 1.5...22,5L/h
- compressor power consumption: 0...5kW
Dimensions and Weight
LxWxH: 2420x780x1900mm
Weight: approx. 280kg
Required for Operation
400V, 50Hz, 3 phases or 230V, 60Hz/CSA, 3 phases
Scope of Delivery
1 trainer
1 set of instructional material

Arrange delivery within 45 days upon receipt of payment.

Please see below photo for detailed package.

Training Room Photo

Company Information

We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today´s and tomorrow´s careers.

Photo for Clients Visiting Factory

Service

We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.

Certificate
Our products takes ISO9001 product management system.