Active Member
|
[China]
Address: 18F, Building 2, Nantai Yunchuanggu, Phoenix Community, Guangming District, Shenzhen, Guangdong, China
Contact name:Amy
Shenzhen FRIDA LCD Co., Ltd |
|
|
10.1 Inch Lcd Display 1280x800 Lvds Interface 40 Pins High Brightness
General Description:
R101B40-226-0101 active area is 216.96(H)*135.6(V)mm,number of pixels is 1280(H)×800(V),pixel pitch is 0.0565(H)×RGB×0.1695(V)mm,pixels RGB stripe arrangement,Normally Black,16.7M(6bit +Hi-FRC) colors.
Specifications:
| Parameter | Specification | Unit |
| Active Area | 216.96(H)*135.6(V) | mm |
| Number Of Pixels | 1280(H)×800(V) | pixels |
| Pixel Pitch | 0.0565(H)×RGB×0.1695(V) | mm |
| Pixel Arrangement | Pixels RGB stripe arrangement | |
| Display Mode | Normally Black | |
| Display Colors | 16.7M(6bit +Hi-FRC) | colors |
| Surface Treatment | HC | |
| Contrast Ratio | 1000:1(typ.) | |
| Viewing Angle(CR>10) | 80/80/80/80(typ.) | |
| Response Time | 35(typ.)/40(max.) | ms |
| Color Gamut | 50%NTSC | |
| Power Consumption | Panel: 0.7(Typ.) | watt |
| Outline Dimension | 221.96(H)*144.43(V)*1.06(typ)(FOB -Panel) | mm |
Absolute Maximum Ratings:
| Parameter | Symbol | Min. | Max. | Unit | Remarks | |
Power Supply | LCD Module | VDD | VSS-0.3 | 3.6 | V | Ta = 25 ℃ |
| Operating Temperature | TOP | -20 | +70 | ℃ |
| |
| Storage Temperature | TST | -30 | +80 | ℃ | ||
| Operating Ambient Humidity | Hop | 10 | 90 | %RH | ||
| Storage Humidity | Hst | 10 | 90 | %RH | ||
Electrical Specifications:
Parameter | Symbol | Values | Unit | |||
| Min. | Typ. | Max. | ||||
Power Supply Voltage | VDD | 3.0 | 3.3 | 3.6 | V | |
| VRP | 300 | mV | ||||
| Power Supply Current | IDD | - | 212 | 364 | mA | |
| Power Consumption | PLCD | - | 0.7 | 1.2 | W | |
| Rush current | IRUSH | - | - | 3.0 | A | |
CMOS Interface | Input Voltage | VIH | 2.7 | 3.3 | V | |
| VIL | 0 | 0.5 | V | |||
Output Voltage | VOH | 2.7 | 3.3 | V | ||
| VOL | 0 | 0.5 | V | |||
Interface Connection:
| Pin No. | Symbol | Description | I/O |
| 1 | NC | Non Connection | - |
| 2 | VDDIN | Power supply VDDIN=3.3V (Typ.) | P |
| 3 | VDDIN | P | |
| 4 | VDDIN | P | |
| 5 | NC | Non Connection | - |
| 6 | GND | GROUND | P |
| 7 | GND | GROUND | P |
| 8 | RIN0- | LVDS Negative data signal (-) | I |
| 9 | RIN0+ | LVDS Positive data signal (+) | I |
| 10 | GND | GROUND | P |
| 11 | RIN1- | LVDS Negative data signal (-) | I |
| 12 | RIN1+ | LVDS Positive data signal (+) | I |
| 13 | GND | GROUND | P |
| 14 | RIN2- | LVDS Negative data signal (-) | I |
| 15 | RIN2+ | LVDS Positive data signal (+) | I |
| 16 | GND | GROUND | P |
| 17 | LVDS_CLK- | LVDS Negative CLK signal (-) | I |
| 18 | LVDS_CLK+ | LVDS Positive CLK signal (+) | I |
| 19 | GND | GROUND | P |
| 20 | RIN3- | LVDS Negative data signal (-) | I |
| 21 | RIN3+ | LVDS Positive data signal (+) | I |
| 22 | GND | GROUND | P |
| 23 | NC | Non Connection | - |
| 24 | NC | Non Connection | - |
| 25 | GND | GROUND | P |
| 26 | NC | Non Connection | - |
| 27 | NC | Non Connection | - |
| 28 | GND | GROUND | P |
| 29 | NC | Non Connection | - |
| 30 | NC | Non Connection | - |
| 31 | LED- | LED Cathode | O |
| 32 | LED- | O | |
| 33 | LED- | O | |
| 34 | NC | Non Connection | - |
| 35 | NC | Non Connection | - |
| 36 | NC | Non Connection | - |
| 37 | NC | Non Connection | - |
| 38 | LED+ | LED Anode | P |
39 | LED+ | P | |
| 40 | LED+ | P |
Optical Specification:
| Item | Symbol | Condition | Min | Typ. | Max | Unit |
Viewing Angle | θL | Cr≥10 | 70 | 80 | -- | deg |
| θR | 70 | 80 | -- | |||
| θT | 70 | 80 | -- | |||
| θB | 70 | 80 | -- | |||
| Contrast Ratio | Cr | θ=0° FF=0° | -- | 1000 | - | |
| Response Time | Tr+Tf | -- | 35 | 40 | ms | |
Color Coordinate of CIE1 931 | Rx | θ=0° | -- | - | ||
| Ry | -- | |||||
| Gx | -- | |||||
| Gy | -- | |||||
| Bx | -- | |||||
| By | -- | |||||
| Wx | -- | |||||
| Wy | -- | |||||
| NTSC Ratio | NTSC | CIE1931 | 45 | 50 | -- | % |
| Gamma | - | 1.9 | 2.2 | 2.5 | ||
| Polarization Direction of Front Polarizer | - | 0 | deg | |||
| Polarization Direction of Rear Polarizer | PdR | 90 | deg | |||
Handling Precautions:
1.It is indispensable to drive the LCD within the specified voltage limit since the higher Voltage than the limit causes the shorter LCD's life. An electro-chemical reaction due to DC causes undesirable deterioration of the LCD so that the use of DC drive should avoid.
2.Do not connect or disconnect the LCD to or from the system when power is on.
