Active Member
|
[China]
Address: 18F, Building 2, Nantai Yunchuanggu, Phoenix Community, Guangming District, Shenzhen, Guangdong, China
Contact name:Amy
Shenzhen FRIDA LCD Co., Ltd |
|
|
11.6 Inch 1920x1080 Tft All Viewing Angle 30 Pin Edp 220 Nit
General Description:
The manufacturer of M116B30-040-121-0102 is BOE, this Open-cell is a color active matrix LCD open-cell incorporating Oxide TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, a control circuit and power supply circuit.
Specifications:
| Parameter | Specification | Unit | Note |
| Display size | 11.6” (Diagonal) | inch | |
| Active area | 256.32(H) ×144 . 18(V) | mm | |
| Pixel Format | 1920(H) ×1080(V) (1pixel = R + G + B dot) | pixel | |
| Pixel pitch | 0.1335(H) x 0.1335 (V) | mm | |
| Pixel configuration | R, G, B vertical stripe | ||
| Display mode | Normally black | ||
Surface treatment of front polarizer | Anti-glare coating: (3H) |
Interface Connection:
CN1 (eDP signals , +3.3V DC power supply and B/L power supply)
| Pin No. | Symbol | I/O | Function | Remark |
| 1 | CABC_EN / NC | - | Reserved for CD | [Note1] |
| 2 | H_GND | P | High Speed round | [Note2] |
| 3 | Lane1_N | I | Complement Signal Link Lane 1 | |
| 4 | Lane1_P | I | True Signal Link Lane 1 | |
| 5 | H_GND | P | High Speed round | [Note2] |
| 6 | Lane0_N | I | Complement Signal Link Lane 0 | |
| 7 | Lane0_P | I | True Signal Link Lane 0 | |
| 8 | H_GND | P | High Speed round | [Note2] |
| 9 | AUX_CH_P | I | True Signal Auxiliary Channel | |
| 10 | AUX_CH_N | I | Complement Signal Auxiliary Channel | |
| 11 | H_GND | P | High Speed round | [Note2] |
| 12 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
| 13 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
| 14 | NC | I | Reserved for LCD manufacturer’s use | [Note1] |
| 15 | LCD_GND | P | LCD logic and driver ground | |
| 16 | LCD_GND | P | LCD logic and driver ground | |
| 17 | HPD | O | HPD signal pin | |
| 18 | LED-1 | P | Backlight ground | |
| 19 | LED-2 | P | Backlight ground | |
| 20 | LED-3 | P | Backlight ground | |
| 21 | LED-4 | P | Backlight ground | |
| 22 | BL_ENABLE | I | Backlight on/off | |
| 23 | BL_PWM_DIM | I | System PWM | |
| 24 | SCL/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
| 25 | SDA/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
| 26 | BL_PWR | P | Backlight power | |
| 27 | BL_PWR | P | Backlight power | |
| 28 | BL_PWR | P | Backlight power | |
| 29 | BL_PWR | P | Backlight power | |
| 30 | NC | - | Reserved for LCD manufacturer’s use | [Note1] |
[Note]:P: POWER I: Input O: Output
[Note1] Don’t input any signals or any powers into a NC pin. Keep the NC pin open.
[Note2] The shielding case is connected with signal GND.Connector used :20455-030E-76(I-PEX),Corresponding connector : 20453-030T (I-PEX)
Absolute Maximum Ratings:
| Parameter | Symbol | Condition | Ratings | Unit | Remark | |
| MIN | MAX | |||||
| +3.3V supply voltage | VDD | Ta=25℃ | -0.3 | +3.6 | V | |
| Backlight supply voltage | VBL | Ta=25℃ | -0.3 | +21 | V | |
| Input voltage(eDP) | VI | Ta=25℃ | -0.3 | +1.5 | V | [Note1] |
| Input voltage(BL) | VBL_I | Ta=25℃ | -0.3 | VDD+0.3 | V | [Note2] |
| Storage temperature | Tstg | -10 | +60 | ℃ |
| |
| Operation temperature | Topa | 0 | +50 | ℃ | ||
“Absolute Maximum Ratings” is regulations that do not exceed it even momentarily.
Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
[Note1] eDP signals
[Note2]Backlight control signals (BL_ENABLE,BL_PWM_DIM)
TFT-LCD Panel Driving:
| DC Electrical Characteristics | ||||||
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
| +3.3V supply voltage | VDD | +3.0 | +3.3 | +3.6 | V | |
| Permissible input ripple voltage | VRP | - | - | 100 | mVp-p | VDD=+3.3V |
| eDP HPD Signal Characteristics | ||||||
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
| HPD High level output voltage | VOHHPD | VDD-0.1 | ||||
| HPD Low level output voltage | VOLHPD | |||||
| eDP AUX Channel Characteristics | ||||||
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
| Unit Interval for AUX channel | UIAUX | 0.4 | 0.5 | 0.6 | S | |
| Peak-to-peak voltage at TP1 | VAUX-DIFF-pp | 0.32 | - | 1.36 | V | |
| AUX DC Common mode Voltage | VAUX-DC-CM | 0 | - | 2.0 | V | |
| AUX Short current limit | IAUX_SHORT | - | - | 90 | mA | |
| AUX CH termination DC resistor | RAUX_TERM | - | 100 | - | Q | Differential input |
| AUX AC coupling capacitor | CAUX | 75 | - | 200 | nF | |
| Number of pre-charge pulses | Pre-charge pulses | 10 | - | 16 | - | |
| eDP AUX Channel Characteristics | ||||||
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
| Link clock down spreading | Down_Spread_Am plitude | 0 | 0.5 | % | ||
| Differential Peak-to-peak Input Voltage at Rx package pins | VRX-DIFFp-p | 90 | 1200 | mV | ||
| Differential Return Loss at 1.35GHz at Rx package pins | RLRX-DIFF | 9 | - | - | dB | |
Differential termination resistance | RRX-TERM | - | 100 | - | Q | |
| RX short circuit Current Limit | IRX-SHORT | - | 50 | mA | ||
| Lane Intra-pair Skew at RX package pins | TRX-SKEW- NTRA- PAIR-High-Bit-Rate |
- |
- | TBD | ps | |
Backlight Driving:
The backlight system is an edge-lighting type with white-LED.
(It is usually required to measure under the following condition: Ta=25C±2C)
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
| Supply voltage | VBL | 7.0 | 12.0 | 21.0 | V | |
Current dissipation | IBL | - | (227) | (251) | mA | VBL=12V Duty Ratio=100% |
| (135) | (135) | mA | VBL=7.9V Duty Ratio=40% | |||
| Modulated light signal voltage | VPWM H | 1.85 | - | VDD | V | |
| VPWM L | 0 | - | 0.7 | V | ||
| Brightness Control Duty Ratio | Duty | 1 | - | 100 | % | [Note6-3-1] |
| Brightness Control pulse width | TPWM | 5 | - | - | ps | [Note6-3-2] |
| Brightness Control frequency | PWM | 200 | - | 2,000 | Hz | |
| LED-BL ON/OFF High voltage | VCNT H | 1.8 | 3.3 | 3.6 | V | [Note6-3-3] |
[Note6-3-1]Vpwm Input : 100%= Max luminance 1%= Min luminance
[Note6-3-2]The minimum value of the dimming signal pulse width is assumed regulations of the width of high and the width of low.
[Note6-3-3]VCNT Input : High = BL turn on, Low or OPEN =BL turn off
VBL-dip conditions
Optical Specification:
| Paramete | Conditions | Min. | Typ. | Max. | Unit | |
Viewing Angle(CR>10) | Horizontal | L | - | 89 | - | degree |
| R | - | 89 | - | |||
| Vertical | T | - | 89 | - | ||
| B | - | 89 | - | |||
| Contrast Ratio | Center | 700 | 1000 | - | - | |
| Response Time | Tr+Td | - | 25 | ms | ||
CF Color Chromaticity(CIE1931) | Red x |
Typ. -0.05 | TBD |
Typ. +0.05 | - | |
| Red y | TBD | - | ||||
| Green x | TBD | - | ||||
| Green y | TBD | - | ||||
| Blue x | TBD | - | ||||
| Blue y | TBD | - | ||||
| White x | (0.313) | - | ||||
| White y | (0.329) | - | ||||
| NTSC ratio | % | (72) | - | |||
| Luminance of white | YLI | 220 | cd/m | |||
The measurement shall be taken 30 minutes after lighting the module at the following rating.
Condition: PWM Duty = 100%
The optical characteristics shall be measured in a dark room or equivalent.
Matters Needing Attention:
1.Be sure to turn off the power supply when inserting or disconnecting the cable. Please insert for too much stress not to join a connector in the case of insertion of a connector.
2.Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist.
3.Since the front polarizer is easily damaged, pay attention not to scratch it.
4.Wipe off water drop immediately. Long contact with water may cause discoloration or spots .
5.When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
6.Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care.
Reliability Test Items:
| No. | Test Item | Conditions |
| 1 | High temperature storage test | Ta=60℃ 72h |
| 2 | Low temperature storage test | Ta=-10℃ 72h |
| 3 | High temperature & high humidity operation test | Ta=40℃90%RH 72h (No condensation) |
| 4 | High temperature operation test | Ta=50℃ 72h |
| 5 | Low temperature operation test | Ta=0℃ 72h |
