Led Digital Packaging Drop Test Machine / Electric Widening Arms Drop Test Machine

 
Led Digital Packaging Drop Test Machine Electric Widening Arms Drop Test Machine​
 
 
Electric widening double-arm drop test machine JD-6001B
 
 
First, the product uses:
 
The double-arm drop tester is mainly used to assess the degree of impact of the package on the actual transportation, loading and unloading process, and to assess the impact strength and packaging design of the package during the handling process. The drop test machine uses the brake motor through the chain. The transmission drives the drop arm to extend and descend. The drop height is adopted in the digital height scale. The drop height is accurate, the display is intuitive, the operation is simple, the drop arm is lifted smoothly, and the drop angle error is small. This machine is suitable for various manufacturers and quality inspection departments.
 
 
Second, meet the design criteria:
 
The falling test of the two arms meets the national standards of GB4757.5-84 JISZ0202-87 ISO2248-1972(E).
 
 
Third, the test principle:
 
The test sample is lifted to a predetermined height, and then it is freely dropped in a predetermined state to collide with the impact table. After the product is packaged, it is damaged by the fall, and the impact strength of the electronic component is evaluated when it is moved. The angle and surface of the packaging container can be tested;
 
 
Fourth, the main technical parameters:
 
1. Drop height: 200-1200MM
 
2, the maximum weight of the test piece: 150Kg; electric drop
 
3. Height display mode: LED digital
 
4. Drop floor thickness: 20mm
 
5. Drop method: electric
 
6. Reset method: manual
 
7. Sample clamping method: diamond, angle, surface (all-round drop)
 
8. Arm size; 1600*400mm
 
9, the largest size of the test piece: 3200 * 800 * 500mm;
 
10, the size of the bottom plate: 3500 * 1200 * 20mm
 
11, motor power: 1.5kw
 
12, the arms are electrically adjusted width, arms moving distance; 700-3200
 
13. Test bench dimensions: 3500*1200*1800mm
 
14, drop error: ± 10mm;
 
15, drop plane error <1°
 
16, height display using high precision encoder induction
 
17. Control box: Separate vertical control box with anti-static powder paint.
 
18. Net weight: 1800kg
 
19, power supply: 380V, 1.5KW
 
 
Five, equipment operation specifications
 
1. Turn on the power switch and the power light is on. (At this time, it is strictly forbidden for personnel without professional training to enter the yellow warning line to do any relevant test operation. It is very dangerous), check whether the two wings are in the horizontal position, otherwise the hand plate is in the horizontal position;
 
2. Place the test specimen on the two wings and fix it with a clamp; everyone stands outside the safety line.
 
3. Press the up button to raise the two wings to the required test height, and press the stop button to stop the rise;
 
4. Press the falling key, the test item is free to fall, the test is completed, and the sample condition after the drop test is recorded;
 
5. Test the other products according to the above 2~4 test methods, and perform the free drop test according to the required surface, angle and edge.
 
6. Remarks: It is strictly forbidden to stand on the workbench during the drop test! (Danger)
 
 
Sixth, matters needing attention and maintenance
 
1. The test machine casing must be grounded reliably, otherwise there is danger of electric shock;
 
2. The power inlet end should be connected with air switch and contactor with leakage protection above the same capacity, so that the power can be cut off immediately in case of emergency;
 
3. When the machine is running, do not touch the part other than the control panel with your hand to prevent scratches or crushing;
 
4. If you need to move the machine, be sure to cool it for 5 minutes after turning off the power.
 
5. After the new machine is installed in the factory, it is necessary to add appropriate low-concentration oil to the sliding round rod. It is strictly forbidden to add anti-rust oil or high-concentration oil and backlog with corrosive oil.
 
6. If there is too much dust in the oiling station for a long time, please lower the machine to the lower part, wipe the previous oil and re-oil it; regularly add lubricating oil to the transmission parts of the machine;
 
7. The drop machine is an impact mechanical device. When the new machine is used more than 500 times, each screw must be tightened to avoid malfunction.
 
 
Seven, machine studio environment requirements
 
Temperature: 5 ° C ~ +28 ° C [1] (average temperature within 24 hours ≤ 28 ° C)
 
Relative humidity: ≤85% RH
 
Power supply conditions Three-phase four-wire + protective ground wire,
 
Voltage range: AC (380 ± 38) V