|
[China]
Trade Verify
Address: NO.161 BA YI SOUTH STREET, JINHUA CITY, ZHEJIANGPROVINCE, CHINA
Contact name:Grace
China Lichuang Steel CO.,Limited |
|
Verified Suppliers
|
|
|
ASTM A240/A240M Middle Thick Stainless Steel Plate 8MM S32205 Heat Resistant Inox Sheet
Hot forming
ASTM A240/A240M Middle thick stainless steel and 2205 duplex stainless steel sheet forming shall be carried out below 600 ° F. During hot forming treatment, the whole workpiece shall be heated as a whole and shall be carried out in the temperature range of 1750 ° f to 2250 ° F. 2205 alloy is very soft at this temperature. If the temperature is too high, 2205 alloy is prone to hot tearing. Below this temperature, austenite will fracture. Below 1700 ° F, the intermetallic phase will form quickly due to the influence of temperature and deformation. After hot forming, it shall be subject to solid melt annealing at a minimum temperature of 1900 ° F and quenching to restore its phase balance, toughness and corrosion resistance. We do not recommend stress relief, but if this is necessary, the material should be solid melt annealed at a minimum temperature of 1900 ° F, then rapidly cooled and water quenched.
Cold forming
ASTM A240/A240M Middle thick stainless steel and 2205 duplex stainless steel sheet can be cut and cold formed. However, due to its high strength and hardness, 2205 alloy needs cold forming more than austenitic steel. Because of its high strength, springback should be fully considered.
Mechanical machinability
On high-speed machine tools, the feed rate and cutting speed of 2205 stainless steel plate are the same as 316L. If the carbonization knife is used, the cutting speed is reduced by about 20% compared with 316L. The performance of machinery and equipment and its components plays a key role here.
heat treatment
ASTM A240/A240M Middle thick stainless steel and 2205 duplex stainless steel sheet applied to solid melt annealing and stress relief. If the stress relief treatment is carried out at a temperature lower than 1900 ° F, it is easy to lead to the precipitation of harmful metallic or non-metallic phases.
| Product Name | ASTM A240/A240M Middle thick stainless steel and 2205 duplex stainless steel sheet |
| Length | 1M 1.5M 2M 3M 5.8M Or as required |
| Width | 3mm-2500mm or as required |
| Thickness | 0.03mm-300mm or as required |
| Standard | AISI,ASTM,DIN,JIS,GB,JIS,SUS,EN,etc |
| Technique | Hot rolled / cold rolled |
| Surface Treatment | NO.1 2B or according to customer requirement |
| Thickness Tolerance | ±0.01mm |
| Material | 201, 202, 301, 302, 303, 304, 304L, 304H, 310S, 316, 316L, 317L, 321,310S 309S, 410, 410S,420, 430, 431, 440A,904L |
| Application | It is widely used in high temperature applications, medical
devices, building materials, chemistry, food industry, agriculture,
ship components. It also applies to food, beverage packaging, kitchen supplies, trains, aircraft, conveyor belts, vehicles, bolts, nuts, springs, and screen. |
| MOQ | 1 ton , We can accept sample order. |
| Shipment Time | Within 3-5 workdays after receiving deposit or L/C |
| Export Packing | Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required |
| Capacity | 250,000 tons/year |
Chemical Composition:
| Grade | C | Si | Mn | P | Ni | Cr | Mo |
| 201 | ≤0.15 | ≤0.75 | 5.5-7.5 | ≤0.06 | 3.5-5.5 | 16.0-18.0 | - |
| 202 | ≤0.15 | ≤1.0 | 7.5-10.0 | ≤0.06 | 4.-6.0 | 17.0-19.0 | - |
| 301 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.045 | 6.0-8.0 | 16.0-18.0 | - |
| 302 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.035 | 8.0-10.0 | 17.0-19.0 | - |
| 304 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.045 | 8.0-10.5 | 18.0-20.0 | - |
| 304L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | 9.0-13.0 | 18.0-20.0 | - |
| 309S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.045 | 12.0-15.0 | 22.0-24.0 | - |
| 310S | ≤0.08 | ≤1.5 | ≤2.0 | ≤0.035 | 19.0-22.0 | 24.0-26.0 | - |
| 316 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.045 | 10.0-14.0 | 16.0-18.0 | 2.0-3.0 |
| 316L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.045 | 12.0-15.0 | 16.0-18.0 | 2.0-3.0 |
| 321 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | 9.0-13.0 | 17.0-19.0 | - |
| 630 | ≤0.07 | ≤1.0 | ≤1.0 | ≤0.035 | 3.0-5.0 | 15.5-17.5 | - |
| 631 | ≤0.09 | ≤1.0 | ≤1.0 | ≤0.030 | 6.50-7.75 | 16.0-18.0 | - |
| 904L | ≤2.0 | ≤0.045 | ≤1.0 | ≤0.035 | 23.0-28.0 | 19.0-23.0 | 4.0-5.0 |
| 2205 | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.030 | 4.5-6.5 | 22.0-23.0 | 3.0-3.5 |
| 2507 | ≤0.03 | ≤0.80 | ≤1.2 | ≤0.035 | 6.0-8.0 | 24.0-26.0 | 3.0-5.0 |
| 2520 | ≤0.08 | ≤1.5 | ≤2.0 | ≤0.045 | 0.19-0.22 | 0.24-0.26 | - |
| 410 | ≤0.15 | ≤1.0 | ≤1.0 | ≤0.035 | - | 11.5-13.5 | - |
| 430 | ≤0.12 | ≤0.75 | ≤1.0 | ≤0.040 | ≤0.60 | 16.0-18.0 | - |
Mechanical Property:
| Grade | Tensile Strength (Mpa) | Yield Strength (Mpa) | Elogation(%) | Hardness (HRB) |
| 201 | ≥655 | ≥310 | ≥40 | ≤100 |
| 202 | ≥620 | ≥260 | ≥40 | ≤100 |
| 304 | ≥515 | ≥205 | ≥40 | ≤92 |
| 304L | ≥485 | ≥170 | ≥40 | ≤88 |
| 316 | ≥515 | ≥205 | ≥40 | ≤95 |
| 316L | ≥485 | ≥170 | ≥40 | ≤95 |
| 321 | ≥515 | ≥205 | ≥40 | ≤95 |
| 409 | ≥380 | ≥205 | ≥20 | ≤80 |
| 409L | ≥350 | ≥185 | ≥22 | ≤80 |
| 430 | ≥450 | ≥205 | ≥22 | ≤80 |
Detailed Photos:
Packing & Shipping
About Us
HENGCHENGTAI SPECIAL STEEL CO .,LTD IS LOCATED IN SHANGHAI, THE LARGEST STEEL DISTRIBUTION CENTER IN EAST CHINA. SINCE ITS ESTABLISHMENT, THE COMPANY HAS BEEN COMMITTED TO PROVIDING CUSTOMERS WITH HIGH-QUALITY STEEL MATERIALS AND HAS BECOME THE LEADING SUPPLIER OF COMPREHENSIVE MATERIAL SOLUTIONS IN CHINA. THE COMPANY HAS 20,000 SQUARE METERS OF INDOOR STORAGE, MORE THAN 20,000 TONS OF SPOT INVENTORY.
FAQ
Q1: ARE YOU FACTORY OR TRADER?
A1: Hengchengtai Special Steel is a cold rolling manufacturer of
magnetic stainless steel coil since 2009. We've gained our Export
Right and become an integrated company of industry and trade in
order to satisfy buyer's multi-request on different material and
products.
Q2: WHICH MATERIAL/PRODUCTS YOU CAN PROVIDE?
A2: Stainless Steel Coils / Strips, Stainless Steel Sheets / Plates,
Stainless Steel Circles / Discs, Decorative Stainless Steel Sheets.
Q3: HOW TO GET A SAMPLE?
A3: FREE samples are available for your checking and testing. And to
get free samples, you need to send us you detailed receiving
address (including post code) and your DHL/FedEx/UPS account for
collecting samples, courier cost will be paid in your side.
Q4: HOW TO VISIT YOUR FACTORY?
A4: Most of the main cities have flights to Shanghai; you can take
flight to Shanghai Putong/Hongqiao International Airport.
If you come from Hongkong, it will take 2 hours by flight (every
day 5 flight around noon time).
