|
[China]
Trade Verify
Address: Room 101, 1st Floor, No. 6, Third Street, Pingshan Industrial Zone 511495, Shibi Street, Panyu District, Guangzhou, China
Contact name:Zoe Zou
Sinuo Testing Equipment Co. , Limited |
|
Verified Suppliers
|
|
|
IEC 62196-1 Electric Vehicle Terminal Test Equipment Mechanical Tests On Terminals
Product Information For Electric Vehicle Terminal Test Equipment:
This testing machine conforms to IEC 62196-1:2020 clause 13.3.1 fig12, table 3, etc. It is used to process mechanical tests on terminals, for judging whether the design and the structure of the new terminals are fitted with new conductors and of the minimum and the maximum cross-sectional areas is good. Besides, it is also used to check whether the clamping screw terminal can bear the stress during the process of normal usage.
The testing times can be preset before the test, and the test
machine will stop automatically with completion alarm when the
preset test times are reached.
Technical Parameters For Electric Vehicle Terminal Test Equipment:
| Parameter Name | Parameter Data |
| Power Supply | AC220V, 60Hz |
| Test Station | Single |
| Test Rate | (10 ± 2) r/min |
| Diameter of Gyration | 75mm |
| Test Times | 1-999999times |
| Load Weight | 0.4-70.3Kg |
| Test Height | 260-660mm adjustable |
| Diameter of Bushing | 6.5mm, 9.5mm, 13mm, 14.5mm, 15.9mm, 19.1mm, 22.2mm, 25.4mm, 28.6mm, 31.8mm, 38.1mm, 44.5mm |
| Equipment Dimensions & Weight | L 600mm* W 600mm * H1680mm, approx. 350KG |
Normal Test Steps For Electric Vehicle Terminal Test Equipment:
●Set the test cycles according to the test time, IEC 62196-1:2020 clause 13.3.1 requires the duration of the test is 15 min, equal to (150 ± 30) cycles. (If operator needs to change the test cycles, operator must press the RST button on the counter to eliminate the previously set test cycles)
●Press the "START" button, the equipment starts to test, the turntable rotates at a speed of (10 ± 2) r/min, when the test cycles reach the set value, the test automatically stops with an audible prompt (operator can press the “STOP” button during test to stop test).
●Press the RST button on the counter to cancel the sound prompt. After the test, cut off the power supply.
Weight Distribution Table For Electric Vehicle Terminal Test Equipment:
| Weight with hook | 0.4kg*1, 0.7 kg*1, 0.9 kg*1, 1.4 kg*1, 2 kg*1, 4.5 kg*1, 9.5 kg*1, 19.5 kg*1, 24.2 kg*1 |
| Weight with hole | 0.7 kg*4, 0.8 kg*2, 0.9 kg*3, 3.2kg*1, 4.5 kg*1, 4.6 kg*1, 25 kg*1 |
| How to combinate the weight: | |
| 0.4kg | 0.4kg+small wire clamp |
| 0.7kg | 0.7kg+small wire clamp |
| 0.9kg | 0.9kg+small wire clamp |
| 1.4kg | 1.4kg+small wire clamp |
| 2.0kg | 2.0kg+small wire clamp |
| 2.9kg | 2+0.9+small wire clamp |
| 4.5kg | 4.5kg+small wire clamp |
| 6.8kg | 4.5 kg +0.9 kg +0.7 kg*2+small wire clamp |
| 9.5kg | 9.5 kg +small wire clamp |
| 10.4kg | 9.5 kg +0.9 kg +small wire clamp |
| 14kg | 9.5 kg +4.5 kg +small wire clamp |
| 15kg | 9.5 kg +0.9 kg +0.7 kg *2+3.2 kg +small wire clamp |
| 16.8kg | 9.5 kg +4.5 kg +0.7 kg*4+small wire clamp |
| 20kg | 9.5 kg +4.6 kg +4.5 kg +0.7 kg*2+small wire clamp |
| 22.7kg | 9.5 kg +4.5 kg +4.6 kg +0.9 kg*3+0.7 kg*2+small wire clamp |
| 50kg | 24.2kg+25kg+0.8kg+large wire clamp |
| 70.3kg | 19.5kg+24.2kg+25kg+0.8kg+0.8kg+large wire clamp |
