|
[China]
Trade Verify
Address: No.755, Xianyuehuan Rd, Tianyuan District, Zhuzhou, Hunan Province
Contact name:Shirley
Zhuzhou Ruideer Metallurgy Equipment Manufacturing Co.,Ltd |
|
Verified Suppliers
|
|
|
500*500*1200-6MPA Sinter-HIP Furnace for sintering of precision ceramics
Equipment function
Automatic positive and negative leak detection function
Ar carrier gas differential pressure dewaxing function
Hydrogen micro positive pressure dewaxing function
Vacuum sintering function
Ar partial pressure sintering function(Static and dynamic partial
pressure)
Pressure sintering function
Rapid cooling function (built-in heat exchanger)
Automatic control function
Safety interlock function
Break point reheating function
Equipment system
It mainly includes control system, heating system, positive and
negative pressure debinding system,vacuum system, pressure
sintering system, cooling water system, rapid cooling system,
safety system and auxiliary system.
Design standards
The precision ceramics sinter-HIP furnace is a single chamber and
double door horizontal and periodic heating structure,which is
designed for easy handling and maintenance, the whole process is
controlled automatically.It can realize full load continuous
operation, 300 furnace times/year or 300 working days/year.It uses
graphite element resistance heating (low voltage, high current) .In
addition, there are multiple heating units, each of which controls
the temperature separately.It equipped with fully automatic control
function and safety interlock function.The whole process is
automatically controlled, monitored, tracked and recorded by
computer.The PLC, industrial computer (PC) control to realize the
whole process of one-key start, real-time dynamic monitoring,
computer will save temperature, pressure, vacuum and other
parameters ,alarm interlocking is safe and reliable.
General equipment requirements
Mainly used in precision ceramics dewaxing (Ar carrier gas dewaxing
and hydrogen micro-positive pressure dewaxing), vacuum sintering,
partial pressure sintering (static, dynamic), pressure sintering,
rapid cooling and other processes.It meets the strict requirements
of the uniformity of furnace temperature and atmosphere in the
sintering process of cemented carbide, and the furnace structure
design is advanced and reasonable, which is convenient for
operation and maintenance.The main supporting components (control
components, sensors, graphite heating element, thermocouple, main
control valve, vacuum pump, etc.) have the international advanced
level, can adapt to the long-term, stable, reliable mass production
requirements.At the same time, the equipment meets the national
requirements of energy conservation and environmental protection.
Technical parameters of equipment
Furnace shell design service | 20 years |
Furnace shell design operating time | 6000 furnace/times |
Valid working zone size(W*H*L) | ≥500mm×500mm×1200mm |
| Maximum loading capacity | 1200kg (The load is dependent on the product type) |
Maximum design temperature | 2100℃ ( Heating up the furnace up to 2100℃ under vacuum sintering condition) |
Maximum working temperature | 2000℃ (Under vacuum and pressurization condition) |
| Maximum design pressure | 64bar |
| Maximum working pressure | 58bar |
Pumping speed | The vacuum degree can reach 5Pa within 30min after starting the pump.The ultimate vacuum value reaches 1Pa after reaching 5Pa and pumping for 30min (after drying, cold, empty, dry). |
Leakage rate | ≤3Pa/h (stop the pump group operation and start the test after the limit vacuum is measured after the oven, .Empty furnace, clean, cold state, within 3 hours average value). |
Full furnace loading cooling time
| When the inner furnace fully load materials,the cooling time of sintering temperature from 1450℃ to 100℃ is ≤6h(water temperature≤26℃,55bar≤pressure≤58bar) |
Filling high pressure argon | Intermittent stable charging is adopted, charging time can be set.The system accurately matches the relationship between charging amount and time to ensure the following of charging. |
Wax collect rate | ≥98%(10Kg pure paraffin, argon negative pressure dewaxing.Maximum three mean values). |
Pressurized time | The time of pressurization to 58Bar is ≤15min, which can be set (the gas source pressure is stable within the range of 80-100bar). |
Uninterrupted power supply guarantee time
| Power the indicator light and control the furnace during power off for more than 80 minutes. |
Heating up speed | ≤5℃/min(Under the condition of empty furnace) |
Heating power | About 320KVA |
After sales
1. Installation, Commissioning and Acceptance
We do installation, commissioning and acceptance in buyer's plant.During the installation and commissioning period, the commissioning personnel shall be provided free of charge by the demander according to the staff standard.
The equipment shipped to the buyer, the seller received the buyer's
notification, both within a week to carry the equipment out of the
box together, then check the equipment and all components according
to the packing list . Including equipment accessories, spare parts
and special tools, attached manual and technical documents, etc. It
can be installed after the acceptance check of equipment.
After installation and debugging, the equipment shall be accepted
according to the technical accessories.
2. Training
When taking-over the Furnace to the customer, We will give a staff
training to customer. The operating personnel of the customer
should join to commission,test the furnace, when installing at
customer’s company.
This is practical operation training and practical maintenance
training,and our technical personnel will telling the basic
principle,equipment maintenance knowledge,And the common fault
handling measures.We can training 2 ~ 3 workers. ( Training how to
maintenance and operating.)
3. Warranty period
The warranty period of the equipment is 12 months, which starts from the date of installation and debugging of the supplier. Equipment failure happens, after-sales service personnel shall give solutions within 2 hours, after receiving the buyer's notification . If it is need to go to the site for treatment , operators dispatched by seller should arrive at the site within 48 hours after go aboard. In case of emergency,operators should arrive at the site within 48 hours after go aboard, and continue to make repairs until the fault is removed and the equipment returns to normal.
