|
[China]
Trade Verify
Address: 23E BlockB,Lushan Building,Chunfeng Road,Luohu District,Shenzhen,518001,China
Contact name:Mayne
Wisdomlong Technology CO.，LTD |
|
Verified Suppliers
|
|
|
GE IC693MDL931 OUTPUT MODULE ISOLATED RELAY OUTPUT 8 AMP 8 POINT
N.C. AND FORM C 5-30 VDC OUTPUT 5-250 VAC OUTPUT
Product information GE IC693MDL931 :
The IC693MDL931 is an Isolated Relay Output module from the 90-30
Programmable Logic Controller Series Manufactured by GE Fanuc. It
has a rated voltage of 24 volts DC, 120/240 volts AC, 50/60 Hz
nominally. Each isolated output is for 8 Amp resistive maximum, and
20 Amps maximum per module for UL installations.
It provides the user with 4 normally-closed and 4 Form C relay
circuits for controlling output loads. Each circuit has an output
switching capacity of 8 amps for the normally-closed contacts or
the normally open contacts. Also, each output relay is isolated
from the other relays, and each relay has a separate common power
output terminal. The IC693MDL931, as the rest of the Series 90-30,
is a low-cost solution for high-availability applications, such as:
motor starters, solenoids, and indicators. The user must supply the
AC or DC power to operate the field devices connected to this
module.
When the IC693MDL931 module is used with DC power supply
IC695PSD040 or PSD140, special precautions should be taken because
dropouts in the source voltage will be seen by this module and may
cause relay dropouts. There are no fuses on this module. The
IC693MDL931 module has LED indicators in place, which provide the
ON/OFF status of each point, are located at the top of the module.
The LEDs are arranged in two horizontal rows with eight green LEDs
in each row. This module uses the top row labeled A1 through 8
(points 1 through 8) for output status; the bottom row is not used
and the fuse LED is not used.
An insert goes between the inside and outside surface of the hinged door. The surface towards the inside of the module (when the hinged door is closed) has circuit wiring information, and circuit identification information can be recorded on the outside surface. The outside left edge of the insert is color-coded red to indicate a high-voltage module. The IC693MDL931 can be installed in any I/O slot of a 5 or 10-slot baseplate like an RX3i or in a Series 90-30 PLC system. It is very important to note that this module is not compatible with hot swap operations in any backplane. Hot removing or inserting this module into a backplane can cause damage to the module or other system components.
| Rated Voltage | 24 volts DC, 120/240 VAC, 50/60 Hz (nominal - see the following table for exceptions) |
| Output Voltage Range | 5 to 30 volts DC |
| 5 to 250 VAC, 50/60 Hz | |
| Outputs per Module | Eight isolated outputs |
| Isolation: | |
| Field to Backplane and to Frame Ground | 250 VAC continuous; 1500 VAC for 1 minute |
| Point to Point | 250 VAC continuous; 1500 VAC for 1 minute |
| Maximum Load | 8 Amps resistive maximum per output |
| 20 Amps maximum per module for UL installations Maximum load depends on ambient temperature as shown. | |
| Minimum Load | 10mA |
| Inrush Current | 8 Amps maximum for one cycle |
| On Response Time | 15ms maximum1 |
| Off Response Time | 15ms maximum1 |
| Output Leakage Current | 1mA maximum at 250 VAC, (25°C (77°F)) |
| Power Consumption | 6mA (all outputs on) from 5 volt bus on backplane 110mA (all outputs on) from relay 24V bus on backplane |
| 1 When this module is used with DC power supply IC695PSD040 or PSD140, special precautions should be taken because dropouts in the source voltage will be seen by this module and may cause relay dropouts. | |
IC693MDL931 's details:
Our brand:
1, First, send us the brand, model code/pic of the nameplate, the quantity for inquiry. Then we will send the quote to you. after confirming the model and the quantity, then we will the PI to you.
2, You can transfer by Paypal/ Western Union/Trade assurance/ T/T. When we received the payment, then we will start to prepare the order for you asap.
