|
[China]
Trade Verify
Address: 23E BlockB,Lushan Building,Chunfeng Road,Luohu District,Shenzhen,518001,China
Contact name:Mayne
Wisdomlong Technology CO.，LTD |
|
Verified Suppliers
|
|
|
GE IC697MDL940 OUTPUT MODULE 16 POINT RELAY OUTPUT 16 AMPS 120/240
VAC OR 5/24/125 VDC 480 VA OR 60 WATTS
Product information GE IC697MDL940 :
The IC697MDL940 is a Series 90-70 Programmable Logic Controller
(PLC) module, specifically a Relay output module with a total of
Sixteen (16) relay output channels. Specifically, it has Eight (8)
Form C Contact outputs and Eight (8) Form A or Normally Open (N.O.)
in Two (2) groups of Four (4) Form A contacts each channel. This
module has a nominal voltage rating of 120/240 VAC or 5/24/125 VDC
with a maximum power consumption of 480 VA for AC loads or 60 watts
for DC loads.
It has maximum load current ratings of 2.0 amps from 5 to 265 VAC
at 47-63 Hz; 2.0 amps from 5 to 30 VDC; 0.2 amps from 31 to 125 VDC
and 0.2 amps from 31 to 150 VDC applicable for Form A contact
outputs only while the module’s minimum load current is 10 mA. Each
output channel has a maximum response time of 10 ms for both On and
Off signal transition and switching frequency of 20 Cycles per
minute when used with an inductive load. The output relays of this
module are fixed coil, moving armature type while the output
contacts are made of silver alloy with a maximum contact resistance
of 0.2 Ohm and expected contact life of 20,000,000 operations for
mechanical operations and 1,000,000 electrical operations at
resistive inductive load. Each output of the IC697MDL940 is
installed with a 3 Ampere fuse used as built-in channel protection
along a snubber circuit which consists of a 47 Ohm resistor and
capacitor with 0.015 µfd capacitance value.
The IC697MDL940 output relay module is an output relay module
designed and manufactured by GE Fanuc. The module is typically used
with GE PLC devices from Series 90-70 and it is equipped with 3-Amp
rated fuses for protection. The module has a typical contact life
of 300,000 to 1,000,000 operations and it has a maximum load
current of 0.1 to 2 Amps for a resistive load and 0.05 to 1 Amp for
a inductive load. This particular GE Fanuc module is designed for
both AC and DC operation and it includes operating voltage ratings
of 120 to 240 Volts AC or 5, 24, or 125 Volts DC.
The module has 16 outputs and it features an operating frequency of
47 to 63 Hertz (for AC voltage only). The configuration of the
output points includes 8 points configured in Form C and same
number of points configured in Form A. The output points in Form C
are isolated and other points are placed in 2 groups.
The isolation voltage rating of the GE Fanuc IC697MDL940 output
relay module is 1500 Volts and its switching frequency is 20 cycles
per minute for an inductive load. The module has a maximum output
current leakage of 1 milliAmp at 120 Volts AC and a maximum load
current of 16 Amps per module or 4 Amps per group. The rated
current of the IC697MDL940 module is 750 milliAmps. The module’s
response time is 10 milliseconds and it features a maximum power
rating of 480 Volt-Amps for AC loads and 60 Watts for DC loads. The
IC697MDL940 module has silver alloy contacts with a 0.2-Ohm maximum
resistance rating. The module has a fixed coil relay with a moving
armature.
| Relay Type: | Fixed coil, moving armature |
| Outputs per Module: | 16 |
| Configuration | 8 points - Form C (each point isolated) 8 points - Form A (2 groups with 4 points per group) |
| Isolation: | 1500 volts - any output to backplane 500 volts between Form C circuits or Form A groups |
Maximum Load Current(Resistive) Per Module Per Group (Form A) |
16 amps 4 amps |
| Output Switching Characteristics | |
| Nominal Voltage Rating | 120/240 VAC or 5/24/125 VDC |
| Maximum Power | 480 VA (AC loads) or 60 watts (DC loads) |
| Maximum Load Current (resistive) | 2.0 amps from 5 to 265 VAC (maximum), 47-63 Hz |
| 2.0 amps from 5 to 30 VDC (maximum) | |
| 0.2 amps from 31 to 125 VDC (maximum) | |
| 0.2 amps from 31 to 150 VDC (maximum, Form A only) | |
| Minimum Load Current | 10 mA |
| Maximum Output leakage | 1 mA at 120 VAC |
| Response Time-On: | 10 msec (maximum) |
| Response Time-Off: | 10 msec (maximum) |
| Switching Frequency | 20 cycles/minute (inductive load) |
| Contact Type | Silver alloy |
| Contact Resistance | 0.2 ohm (maximum) |
| Contact Life | Mechanical: 20 x 106 operations |
| Electrical: 105 operations at rated resistive load | |
| Protection (each output) | 3 amp fuse |
| Snubber (R = 47 ohms, C = 0.015 ïfd) | |
| Current Required from 5 V Bus: | 750 mA |
| VME | System designed to support the VME standard C.1 |
IC697MDL940 's details:
Note:
Our brand:
1, First, send us the brand, model code/pic of the nameplate, the quantity for inquiry. Then we will send the quote to you. after confirming the model and the quantity, then we will the PI to you.
2, You can transfer by Paypal/ Western Union/Trade assurance/ T/T. When we received the payment, then we will start to prepare the order for you asap.
