VPI - 1500 Vacuum Pressure Impregnation Equipment Plant Dia 1500*2304mm

VPI-1500 Vacuum Pressure Impregnation Equipment , Vacuum Impregnation Plant

Features:

The vacuum impregnating equipment produced by our company

has the advantage of reliability, working stability, and high energy-efficiency.

Application:

It is used for the insulation treatment of high voltage motors,

traction motors, wind power motors, hydro-generators, anti-explosion motors, and anti-explosion transformers.

Supply Scope:

VPI-1500 double-tank vacuum impregnating equipment, 1 set;

Structural Introduction:

The VPI-1500 vacuum impregnating equipment is comprised of

vacuum pressure impregnating tank, paint storage tank, cleaning tank,

vacuum buffer, exhaust buffer, vacuum system, electrical control system,

heat exchange system, condensation system, anti-explosion system,

paint supply and return system, and heating system.

1) vacuum pressure impregnating tank

a) specification ( inner diameter * linear side height) : ￠1500×1845mm

and ￠1500×2304mm;

c) leakage rate: 0.13Pam3/s,

d) working vacuum degree: 50Pa;

e) vacuum suction time to 50Pa: less than 30min;

f) installation type: vertical;

g) pressurizing medium: clean dry air;

j) tank lid opening type: hydraulic opening;

k) necessary interlock device to prevent misoperation;

Main Components List

2) paint storage tank

a) specification (inner diameter * height): ￠1845×2129mm, 1 pc;

b) erection type: vertical;

c) the storage tank is equipped with sampling valve, pressure relief device and level indicator.

d) mixing device: cycloidal pin-wheel motor; 30-40rpm;

Main Components List

3) cleaning tank

a) specification: ￠400×1000mm, vertical structure, 1 pc; equipped with paint absorption

hole and valves (DN20), level indicator, and sampling hole.

b) erection type: vertical;

c) The system cleans the impregnating tank, pipes, flanges and valves, effectively

avoiding pipe clogging in the middle of working.

d) The cleaning liquid can be used repeatedly without pollution to the environment.

Main Components List

4) vacuum system

a) The vacuum system is comprised of 2X-30 rotary vane pump,main valve, vacuum buffer,

vacuum meter, pipes, and valves.

Main Components

5) vacuum buffer:

The vacuum unit is equipped with a vacuum buffer at the air inlet. This buffer keeps

the solvents out of the vacuum unit, and prolongs the service life of the vacuum unit.

6) filtering buffer:

This paint goes through the filter pipe and stainless valves, and then come into the

impregnating tank. The filter removes impurities out of the paint, and improves the

impregnation effect.

7) cleaning system

The cleaning system connects the cleaning tank and the impregnating tank.

It cleans the impregnation tank, pipes, valves and flanges, and returns the

cleaning liquid to the cleaning tank for use next time.

8) paint supply and return system

a) The paint supply and return sytem works througth the pressure difference. The

level is monitorable at the time of paint supply and return.

b) It is comprised of specially designed filter, paint supply and return valve, pipes, etc.

c) When supplying the paint, the control valve has to be shut down when the paint

level meets the preset value.

FUNCTION: circulation of insulation paint between the impregnating tank and the

paint storage tank.

9) exhaust system

a) The system is comprised of air discharger and pipes.

FUNCTION: The system is used to remove the waste gas of the impregnating

tank and the vacuum pump.

Main Components

10) electrical control system

a) It is comprised of electrical control cabinet, temperature meter, contactor, transformer,

and voltage meter. The control system has a high stability.

Main Components

11)anti-explosion system

The equipment has safety interlock device.

12) hydraulic system

FUNCTION: The system opens or locks the tank lid of the impregnating tank.

Main Components

13) heating system

This system is used to dry the workpieces through 36kw electrical heating tubes.

It is comprised of a fan, heater, high pressure valves, and heat preservation material.

11) submitted material:

a) electrical control system schematic diagram;

b) equipment maintenance guide;

c) outsourced parts manual;

d) easy-worn parts list;

e) maintenance illustrative drawing;

f) pressure vessel quality certificate;

g) spares parts per set: sealing ring, 2 pieces; workpiece basket: 1 piece; glass tube, 1 piece;

Design Specifications:

1) GB1090-1092 ( vacuum rubber sealing method and size);

2) GB16297-1996 ( Emission Standards);

3) Lanzhou Physics Research Institute Vacuum Design Handbook;

4) North East University Vacuum Design Handbook;