|
[China]
Trade Verify
Address: 608, Building B, Yinyi Duhui Guoji, No.8, Lane 559, Youngor Avenue, Haishu District, Ningbo, China
Contact name:Brandon Bao
Ningbo Brando Hardware Co., Ltd |
|
Verified Suppliers
|
|
|
Airtac Type Standard Double Acting Pneumatic Air Cylinders SC Series
Product Features:
1.The seal of piston adopts heterogeneous two way seal structure.
It's dimension is tight and it has the function of grease
reservation.
2.It is tie rod cylinder. The cylinder barrel and front/rear cap is
jointed by tie rods with high reliability.
3.Compared with ISO15552 standard cylinder, SC series cylinder with
the same bore size is shorter.
4.The buffer adjustment of cylinder is smooth and steady.
5.Cylinders and mounting accessories with several specifications
are optional.
6.The seal material with high temperature resistance is adopted to
guarantee the normal operation of cylinder at 150 degrees celsius.
Specifications of SC Series Pneumatic Cylinder:
| Bore Size (mm) | 32 | 40 | 50 | 63 | 80 | 100 | 125 | 160 | 200 | 250 | |
| Acting Type | Double Acting | ||||||||||
| Fluid | Air (to be filtered by 40μm filter element) | ||||||||||
| Mounting Type | SC | Basic FA FB CA CB LB TC TCM1 | |||||||||
| SCD, SCJ | Basic FA LB TC TCM1 | ||||||||||
| Operating Pressure Range | 0.15 to 1.0 MPa (1.5 to 10.0 bar) (22 to 145 psi) | ||||||||||
| Proof Pressure | 1.5 MPa (15 bar) (215 psi) | ||||||||||
| Temprature (℃) | -20 to +70 | ||||||||||
| Speed Range (mm/s) | 30 to 800 | 30 to 500 | |||||||||
| Cushion Type | Variable cushion | ||||||||||
| Adjustable Cushion Stroke (mm) | 21 | 28 | 29 | 36 | 40 | ||||||
| Port Size | 1/8'' | 1/4'' | 3/8'' | 1/2'' | |||||||
Stroke of SC Series Pneumatic Cylinder:
| Bore Size (mm) | Standard Stroke (mm) | Max. Standard Stroke | Max. Stroke |
| 32 | 25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 | 1000 | 2000 |
| 40 | 25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 600 700 800 900 1000 | 1200 | 2000 |
| 50 | 1200 | 2000 | |
| 63 | 1500 | 2000 | |
| 80 | 1500 | 2000 | |
| 100 | 1500 | 2000 | |
| 125 | 1200 | 2000 | |
| 160 | 1500 | 2000 | |
| 200 | 1500 | 2000 | |
| 250 | 1500 | 2000 |
Symbol of SC Series Pneumatic Cylinder:
Ordering Code of SC Series Pneumatic Cylinder:
Criteria for selection: Cylinder thrust:
Installation & Usage:
1. When load changes in the work, the cylinder with abundant output
capacity shall be ed.
2.Relative cylinder with high temperature resistance or corrosion
resistance shall be chosen under the condition of high temperature
or corrosion.
3.Necessary protection measure shall be taken in the environment
with higher humidity, much dust or water drops, oil dust and
welding dregs.
4.Dirty substances in the pipe must be eliminated before cylinder
is connected with pipeline to prevent the entrance of particles
into the cylinder.
5.The medium used by cylinder shall be filtered to 40μm or below.
6.Anti-freezing measure shall be adopted under low temperature
environment to prevent moisture freezing.
7.The cylinder shall be carried out test run without load before
application. Prior to run, buffer shall be turned to the minimum
and gradually released to avoid the damage on cylinder caused by
excessive impact.
8.The cylinder shall avoid the influence of side load in operation
to maintain the normal work of cylinder and extend the service
life.
9. If the cylinder is dismantled and stored for a long time, please
conduct anti-rust treatment to the surface. Anti-dust caps shall be
added in air inlet and outlet ports.
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
Welcome to your any question and inquiry!
