|
[China]
Trade Verify
Address: 608, Building B, Yinyi Duhui Guoji, No.8, Lane 559, Youngor Avenue, Haishu District, Ningbo, China
Contact name:Brandon Bao
Ningbo Brando Hardware Co., Ltd |
|
Verified Suppliers
|
|
|
AC110V DC24V 1/4'' 1/8'' Inch Thread 3 Way 6014 Brass Solenoid Valve
The Type 6014 is a direct-acting solenoid valve system with a brass body. For neutral gases and liquids such as compressed air, natural gas, water and hydraulic oil & Technical vacuum.
1. Port Connection: 1/8'', 1/4'', sub-base
2. Body Material: Brass
3. Seal Material: NBR, FKM, PTFE, EPDM
4. Pressure: 0 to 16 Bar
5. Media temperature ranges covering -10°C to +150°C
Bottom plate installation
When installing the bottom plate, please pay attention to the
allowable load cycle (5W type 100% continuous work, 8W type 60%
intermittent work). The pressure port of the bottom plate is marked
P (R), and the output port is marked A (B). Only ports with the
same function can be connected together.
If the working pressure is consistent with the label, the 6013 type
two-position two-way valve can be installed on the same base plate
with the 6014 type two-position three-way valve with circuit
function C (not D or T!). Under the premise of considering the
function of the valve, the base plate can also be expanded. Several
bottom plates can be connected together with the O-shaped
connecting clip connected to the pressure port P(R).
Note! The unused, open valve port must be sealed with a cover plate
(see accessories).
Main Dimension of 6014 Solenoid Valve:
Technical Data of 6014 Solenoid Valve:
| Model | Orifice Size (mm) | Port Size | Environment Temperature (℃) | Medium Temperature (℃) | Working Pressure (MPa) | CV |
| 6014-01-B | 1 | Sub-base | -20 to +55 | NBR: -5 to +80℃ EPDM: -5 to +120℃ VITON: -10 to +150℃ | 0 to 1.6 | 0.08 |
| 6014-015-B | 1.5 | 0 to 1 | 0.13 | |||
| 6014-02-B | 2 | 0 to 0.8 | 0.13 | |||
| 6014-025-B | 2.5 | 0 to 0.6 | 0.18 | |||
| 6014-01-06 | 1 | 1/8'' | 0 to 1.6 | 0.08 | ||
| 6014-015-06 | 1.5 | 0 to 1 | 0.13 | |||
| 6014-02-06 | 2 | 0 to 0.8 | 0.13 | |||
| 6014-025-06 | 2.5 | 0 to 0.6 | 0.18 | |||
| 6014-01-08 | 1 | 1/4'' | 0 to 1.6 | 0.08 | ||
| 6014-015-08 | 1.5 | 0 to 1 | 0.13 | |||
| 6014-02-08 | 2 | 0 to 0.8 | 0.13 | |||
| 6014-025-08 | 2.5 | 0 to 0.6 | 0.18 |
Valve 6014 is a direct-acting plunger valve. The stopper and
plunger guide tube are welded together to enhance pressure
resistance and leak-tightness. Various seal material combinations
are available depending on the application. The coils are moulded
with polyamide or with chemically resistant epoxy. In combination
with a plug in accordance with DIN EN 175301-803 Form A, the valves
satisfy protection class IP65.
1. Direct-acting and compact valve up to diameter of DN 2.5
2. Vibration-proof, bolted coil system
3. Increased leak-tightness with welded plunger guide tube
4. Energy-saving pulse versions
Brando Factory Production of Brass Solenoid Valves:
As a solenoid valve supplier, BRANDO supplys general purpose solenoid valve for general mediums control. Such as water, air, gas, oil. Offering the cost-effective solution for your projects. Available in brass, stainless steel and PVC material for your projects.
● Size Range: 1/4" to 2" (1/4", 3/8", 1/2", 3/4", 1", 1-1/4",
1-1/2", 2", 2-1/2", 3", 4")
● Voltage: 12 Volt DC, 24 Volt DC, 24 Volt AC, 110 Volt AC, 220
Volt AC
● Pressure: 0-10 bar / 0.3-16 bar
● Temperature: -10℃~180℃
● Material: Brass, Stainless Steel and PVC
● Structure: Direct Acting / Diaphragm / Pilot Operated
● Function: Normally Closed / Normally Open
● Connection Type: Threaded, Flanged, Tri Clamp
● Tolerance: ±10%
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
Welcome to your any question and inquiry!
