18 Seconds Delay Auto Flush For Domestic Ro System Plastic Water Latching Solenoid Valve

18 Seconds Delay Auto Flush For Domestic Ro System Plastic Water Latching Solenoid Valve
 

RO water solenoid valve is used inReverse Osmosis System.The valve is assembled with high quality copper wire solenoid coil, and no leaking armature tube assembly. The valve body is made of Plastic (PP,POM,Nylon). All water Purifier products available in RO are made of food grade plastic for retaining the purity of the soft water .

 

Reverse Osmosis systems

A simple reverse osmosis system consists of a high-pressure pump which increases the pressure of the feed water with salts, ions or impurities. This forces the water across the semi permeable RO (Reverse Osmosis) membrane, leaving behind all the dissolved salts. The required pressure is directly proportional to the salt concentration of the inlet water. The higher the concentration, the higher pressure is required to overcome the osmotic pressure.

The RO membrane lets the cleaner water through and this is called permeate water. The salts and other contaminants which are stopped by the membrane come out as a reject stream. This can be drained out or recycled if possible through the RO system to save water.

The RO systems remove up to 99% of dissolved salts (ions), particles, pathogens and bacteria from feed water.

 
No concentrated water is discharged from the concentrated water pipe
No concentrated water is discharged from the concentrated water pipe, and the TDS value of pure water is the same as that of tap water
Possible reasons:
◆ It may appear after the product has just been installed, the water machine has been disassembled in a larger area, or after the new installation. It may be wrong to connect the water pipe between the high-pressure pump and the RO membrane membrane shell directly to the tee of the rear activated carbon, so that the tap water from the high-pressure pump directly enters the water storage bucket.
Approach:
◆ Correct connection
 
 
Place of Origin: Zhejiang, China
Brand Name: Brando
Model Number: BPV10
Application:ro system,water dispenser, RO system
Material:PP,POM,Nylon
Temperature of Media:Medium Temperature
Pressure:Medium Pressure, max 8 bar
Power:Solenoid
Media:water,air
Port: NPT1/4''
Structure:direct acting, direct acting
Standard or Nonstandard:Standard
Temperature:Medium
 
Main Dimension of RO Solenoid Water Valve:

 
Technical data:

Characteristic	1)Direct acting,0 rated bar pressure.low power 2)compact design to save the space
Medium	Air,water,steam,oil,etc.
Temperature	NBR: -10°C to 80 °C EPDM: -10°C to 120 °C FKM:-10°C to 150 °C
Pressure	0-1.6Mpa
Port Size	1/2''
Port Thread	G, NPT
Orifice	2.5mm
Voltage	DC-12V,24V AC-24V,120V,110V,220V/50HZ
Voltage Range	±10%
Material	Body-Nylon,PP,POM Seal-NBR, EPDM,FKM Amature tube-stainless steel 304 Plunger-stainless steel430F Stop-stainless steel 430F Springs-SS304 Shading rings- stainless steel 304

 
Brando Factory Production of Solenoid Valves:
 

 
Feature:
The solenoid valve is usually used for RO purifier water treatment, with DC24V DC36V voltage option. The valve is assembled with high quality copper wire solenoid coil, and no leaking armature tube assembly. The valve body is made of POM, delrin material, with good performance of strength. And also we assemble special designed o-ring to ensure no leaking while valve working.
Turn on water when system start;and cut off water when system stop.
Domestic RO based water system uses water solenoid valve to control feed and in membrane flushing. Due to lower inlet pressure, pilot operated valves cannot give adequate flow. All water Purifier products available in RO are made of food grade plastic for retaining the purity of the soft water .
 
1.Solenoid valves are the most frequently used control elements in fluidics.
2.Their tasks are to shut off, release, dose, distribute or mix fluids.
3.They are found in many application areas.
4.Solenoids offer fast and safe switching, high reliability, long service life, good medium compatibility of the materials used, low control power and compact design.
 

Reverse Osmosis systems
A simple reverse osmosis system consists of a high-pressure pump which increases the pressure of the feed water with salts, ions or impurities. This forces the water across the semi permeable RO (Reverse Osmosis) membrane, leaving behind all the dissolved salts. The required pressure is directly proportional to the salt concentration of the inlet water. The higher the concentration, the higher pressure is required to overcome the osmotic pressure.
The RO membrane lets the cleaner water through and this is called permeate water. The salts and other contaminants which are stopped by the membrane come out as a reject stream. This can be drained out or recycled if possible through the RO system to save water.
The RO systems remove up to 99% of dissolved salts (ions), particles, pathogens and bacteria from feed water.
 
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
 
Welcome to your any question and inquiry!