Ningbo Brando Hardware Co., Ltd |
Verified Suppliers
|
|
Goyen Type 2'' Inlet 1-1/2'' Outlet Flanged Pneumatic Pulse Valve for Dust Collector Systerm
Goyen Type Flanged dust collector pulse valve with diecast aluminum alloy body, wiedely used in baghouse . Baghouse are the most versatile dust collector style and can be used in all applications. Baghouse collectors with traditional bag filters are preferred for applications with larger or mixed range of dust particle sizes, heavier dust loading, fibrous/sticky dusts or higher temperatures (normally up to 550F, in some cases up to 750F with specialty fabrics).
The working principle :The high-pressure gas enters from the air inlet and enters the
lower air chamber.
1. When the pulse valve is not powered, the gas enters the
decompression chamber through the constant-pressure pipe on the
upper and lower shells and the throttle hole therein. Because the
valve plug blocks the pressure relief hole under the action of the
spring, the gas will not be discharged. Make the pressure in the
decompression chamber and the lower air chamber consistent, and
under the action of the spring, the diaphragm will block the
injection port, and the gas will not burst out.
2. When the pulse valve is energized, the valve core is lifted up
by the electromagnetic force, the pressure relief hole is opened,
and the gas is ejected. Due to the role of the orifice of the
constant pressure pipe, the throughput of the pressure relief hole
is greater than The flow velocity of the pressure pipe gas makes
the pressure in the decompression chamber lower than the pressure
in the lower chamber. The gas in the lower chamber lifts the
diaphragm, opens the blowing port, and performs gas blowing.
Technical Data of CA45FS Flanged Valve:
Model No | CA45FS |
Port Size | 1-1/2'' Outlet 2'' Inlet |
Valve Type | Diaphragm Valve |
Action Type | Pilot Operated |
Connection Type | Flanged Inlet Port |
Temperature Range | -5℃~+55℃ |
Pressure | 0.3~0.8Mpa |
Body Material | Diecast Aluminum Alloy |
Seal Material | NBR(common, all available) |
Voltage | AC24V, AC110V, AC220V, DC24V |
Main Dimension of CA45FS double diaphragm pulse valve:
Details About CA45FS Electromagentic Pulse Valve:
Construction of CA45FS:
Body: Diecast aluminum
Ferrule: 305 SS
Armature: 430FR SS
Seals: Nirtrile or FKM
Spring: 304 SS
Screws: 302 or 304 SS
Outlet Slide Seal: EPDM or FKM
Diaphragm Seat: PA-66(standard). FKM coated mild steel
Connection Surface of CA45FS Diaphragm Pulse Valve:
INSTALLATION of CA45FS AC220V AC110V AC24V DC24V Solenoid Pulse Valve:
1. Prepare inlet flanges and blowtube pipes to suit valve
specification. Avoid installing valves underneath the tank.
2. Ensure tank and pipes are free from dirt, rust or other
particulate.
3. Ensure supply air is clean and dry.
4. Mount valves to inlet flange and blowtube to valves with all
seals in place. Tighten flange bolts to 10Nm (7.4 ft–lbs) Ensure
blowtube is pushed all the way into the valve outlet.
5. Tanks and pipes must be independently supported from valve.
6. Make electrical connections to solenoid or connect RCA pilot
port to pilot valve (RCA valves only).
7. Apply moderate pressure to system and check for installation
leaks.
8. Fully pressurise system.
9. Test fire and listen for proper actuation and crisp pulse
noise.Valve is not a structural component. Do not rely on valve to
retain tanks or pipe. Where used, refer to product
specification for installation details.
Welcome to your any question and inquiry!