Home Companies Ningbo Brando Hardware Co., Ltd

1 1/4 Thread Port 35 Flow Rate Solenoid Control Valve 2W350-35 Direct Drive Series

Contact Us

[China]

Trade Verify

Address: 608, Building B, Yinyi Duhui Guoji, No.8, Lane 559, Youngor Avenue, Haishu District, Ningbo, China

Contact name:Brandon Bao

Ningbo Brando Hardware Co., Ltd

Verified Suppliers

Trust
Seal
Verified
Supplier
Credit
Check
Capability
Assessment

1 1/4 Thread Port 35 Flow Rate Solenoid Control Valve 2W350-35 Direct Drive Series

Country/Region	china
City & Province	ningbo zhejiang
Categories	Valves

Product Details

1 1/4 Thread Port 35 Flow Rate Direct Drive Series Solenoid Control Valve 2W350-35

There are closed chambers in the water solenoid valve. There are through holes in different positions. Each hole leads to different oil pipes. The middle of the cavity is a valve. On both sides are two electromagnets. Which side of the magnet coil is energized? Which side is attracted to, by controlling the movement of the valve body to block or leak different oil drain holes, and the oil inlet hole is normally open, the hydraulic oil will enter different oil drain pipes, and then pushed by the pressure of the oil The piston of the cylinder, the piston drives the piston rod, and the piston rod drives the mechanical device to move. This controls the mechanical motion by controlling the current of the electromagnet.

Specs and Descriptions	2W160-10	2W160-15	2W200-20	2W250-25	2W350-35	2W400-40	2W500-50
Port Size	G3/8	G1/2	G3/4	G1	G1-1/4	G1-1/2	G2
CV Value	4.8	4.8	7.6	12	24	29	48
Type	Normal Closed
Material of Body	Brass
Motion Pattern	Direct Drive
Working Temperature	-5~80℃
Working Pressure	Water/Oil:0~0.5Mpa Air/Gas:0~0.7Mpa
Material of Seal	NBR
Voltage and Way,Position	As your requirement
Liquid	Water Oil Gas Air
Coil	Conventional(Waterproof)

Drawings of 2W350-35

Using Notice

1.The solenoid valve after long-term deactivation should be used after clearing the condensate; when the parts are removed and washed, the parts should be placed in order and

then restored.
2. Please refer to the user manual of the product before installation to see whether it meets your requirements.
3. The pipeline should be cleaned before use, and the filter should be installed if the medium is not clean to prevent impurities from interfering with the normal work of the

solenoid valve.
4. The solenoid valve generally works in one direction and cannot be installed in reverse. The arrow on the valve is the movement direction of pipeline fluid and must be

consistent.

Characteristics

Expanded the field of use with a direct-acting diaphragm structure without pressure start The flat diaphragm structure is reliable in opening and closing and enhances the service life of the product. The use of plastic coils enhances the safe use of this product in a wide range of environments.

Working principles

This valve is the pilot type solenoid valve of the second opening valve. Its structure is mainly composed of the pilot valve and the main valve. The main valve adopts the

rubber sealing structure. When in normal position, the guide valve is sealed with movable iron core, the pressure in the valve chamber is balanced, and the main valve is

closed. When the coil is energized, electromagnetic force is generated to absorb the moving iron core, and the dielectric self-guiding valve mouth in the main valve cavity is

discharged, resulting in pressure difference. The diaphragm or valve cup is quickly lifted, and the main valve mouth is opened, and the valve shows a path. When the coil

power off, the magnetic field disappeared, the resetting of the active iron core, closed valve mouth, valve and the main valve chamber pressure balance, the valve was closed

state.