LCD TFT Multi Parameter Patient Monitor Machine Refurbished

Refurbished Mindray IMEC12 Mutil Parameter Patient Monitor Machine

About Mindray IMEC 

The innovative IMEC Mindray Green Patient Monitor helps you reduce your hospital's environmental footprint and contribute to a sustainable healthcare environment.

Thanks to its optimized equipment design, iMEC consumes 50% less energy than conventional patient monitors. This allows for longer battery life and fanless design for cleaner, quieter operation. It also features a sturdy yet thin and lightweight design, making the iMEC very easy to carry.

The touch screen allows quick and easy operation of the iMEC. With its Wi-Fi capability, iMEC integrates seamlessly with the central monitoring system of the VI Mindray hypervisor.

This gives you easy access to real-time patient information - even during transport.

The default measurement parameters meet all standard clinical requirements and allow the iMEC to operate in a variety of hospital environments, including emergency departments, rehabilitation departments, general departments, and

Outpatient department.

Warning

• All installation operations, expansions, changes, modifications and repairs of this product are conducted by Mindray authorized personnel.

• There is high voltage inside the equipment. Never disassemble the equipment before it is disconnected from the AC power source.
• When you disassemble/reassemble a parameter module, a patient leakage current test must be performed before it is used again for monitoring.

• The equipment must be connected to a properly installed power outlet with protective earth contacts only. If the installation does not provide for a protective earth conductor, disconnect it from the power line and operate it on battery power, if possible.
• Dispose of the package material, observing the applicable waste control regulations and keeping it out of children’s reach.

Multi-parameter module

The NIBP pump and solenoid valve, as well as the multi-parameter module, are located on the bracket of the multi-parameter module, which is mounted on the rear housing with 4 screws.

The multi-parameter module is connected to the connector board with a 2 x 7-pin cable to power the parameter module, communicate with the motherboard, and generate analog outputs and Defib sync outputs. It uses a DSP processor as the core. for ECG

In applications, a self-developed Mindray ECG_ASIC chip is used to perform 3/5/12-lead ECG measurements and RESP (selectable leads I/II), which greatly simplifies sampling and controlling ECG signals for DSPs.

For NIBP, IBP and TEMP measurements, high precision Σ - Δ ADCs are used to generate.

direct sampling of the corresponding parameter signals. Mindray SpO2 measurements were made

stacking connectors. Also fits Nellcorrr and Masi-mo SpO2 cards

Multi-parameter module connected via BTB socket.

• 2-channel ECG parameters with 3/5 leads (12 leads to be developed in the future),selectable I / II cable;
• Mindray / Nellcorrr / Masi-mo SpO2 development and communication;
• TEMP 2 channels;
• 2-channel IBP;
• NIBP parameters;
• Algorithm for all parameters communicates with the motherboard via UART
• serial port; And,
• 4 parallel output interfaces: (1 for EKG, 2 for IBP and one for Defib sync output)
• ECG parameters are isolated separately, while the rest are shielded from the ground.

SpO2 card

The multi-parameter module supports the independently developed Mindray SpO2 board,

Provides SpO2 measurements as good as other cards but in smaller and smaller sizes

to use. Also compatible with Nellcorrr NELL-1 SpO2 and Masi-mo MS-2013 cards

SpO2 card.

The SpO2 board is used to collect the SpO2 signal sent by the multi-parameter module and process the SpO2 algorithm.

NS. Module

NS. the module is located behind the multi-parameter module bracket, facing the multi-parameter module with the bracket in the middle. Available online form M03B, C.O. measurement. NS. modules are standalone subsystems. It is connected to the main board via serial port and interface board.

CO2 module

The CO2 module is also located behind the multi-parameter module bracket, next to the C.O. module. The CO2 module is an independent subsystem. It is connected to the main board via serial port and interface board. The socket of the CO2 module on the interface board, unlike the C.O, has 5 pins. module that prevents corruption.

Three gas modules that can be selected in the appropriate menu,

Patient monitor:

• M02C lateral flow module;
• Traditional Capnostat CO2 module; And,
• Ordion microflow CO2 module.