|
[China]
Trade Verify
Address: Shenzhen, China
Contact name:Fiona Liang
Tianjin Estel Electronic Science and Technology Co.,Ltd |
|
Verified Suppliers
|
|
|
Sandwich Structure Panel Outdoor Power Supply Cabinet With Emerson Rectifier and Battery
1 Product description
1.1 Appearance
After the cabinet is installed, as shown in Figure 1 and Figure 2
Figure 1 Figure 2
1.2 Cabinet configuration
The outdoor integrated cabinet configuration of this project is as follows:
| Cabinet type | Configuration | Quantity | Specifications |
| Main cabinet | 19 inch standard rack | 1 | 31U |
| Battery holder | 1 | 1 layer W×D×H 800×800×350 mm | |
| illumination | 1 | 48V DC, LED light | |
| air conditioning | 1 | AC 220V input, cooling capacity 1500W | |
| air conditioning | 1 | DC 48V input, cooling capacity 300W | |
| Grounding copper bar | 1 | M6 bolts 10 | |
| Busbar | 1 | M6 bolts 10 | |
| AC and DC power distribution unit | 1 | AC input: 63A/2P*1; AC output: 63A/2P*1; DC input : 63A/1P *1; DC output : 16A/1P*1; DC output : 10A/1P*3; DC output : 6A/1P*3 Circuit breaker brand: Schneider | |
| PDU | 1 | 8 -bit universal socket, 220V 16A | |
| Embedded power supply | 1 | Netsure211 C46 / DC48V / 60A / 3U / rectifier module 20A with 3 / Brand: Emerson | |
| battery | 4 | SP12-65/12V/65Ah/ size: 350*167*185/ Brand: Shandong Shengyang | |
| Environmental monitoring system | 1 | GMU/ smoke, flooding, temperature and humidity, tilting vibration, access sensor | |
| Base sealing plate | 1 | 1 set containing 6, before and after one, two right and left |
1.3 Cabinet size
The size of a single cabinet is shown in Figure 3 . External size: W×D×H 905×905×2107mm
Figure 3
1.4 Cabinet material
Sanwich structure panel, galvanized steel, double wall with heat insulation
2 Cabinet installation
2.1 Unpacking
Outdoor integrated cabinets are generally packed in wooden cases. When disassembling the package, take care to avoid damage to the cabinet.
2.2 Cabinet base
The size of the base of the cabinet and the fixing hole of the base expansion bolt are shown in Figure 4 .
Figure 4
2.3 Cabinet fixing
( 1 ) According to the hole position map or the scribe template of the cabinet base, the base expansion bolt hole of the cabinet is punched with a hammer drill in advance, and the diameter of the hole is referenced to the size of the expansion bolt;
( 2 ) First, fix the leftmost or rightmost first cabinet with expansion bolts, place the remaining cabinets one by one, and finally fix the cabinets with the expansion bolts.
( 3 ) If you need to seal the base of the cabinet, use the base sealing plate (optional) to seal the notch and hole around the base. The mounting screws are the M5 stainless steel screws in the cabinet attachment (see Figure 5 ).
Note: If the cement foundation is not flat, it is recommended to use a gasket or spacer to level the base of the cabinet.
Figure 5
Note: When crossing the wire loop, first cut the cross with a utility knife. After the cable is connected, seal the remaining gap on the wire loop with the sealing glue attached to the cabinet.,As shown below;
3 Device debugging
3.1 Air conditioner
Refer to the attached Cabinet Air Conditioner User Manual for relevant.
4. Cabinet picture
