Active Member
|
[China]
Address: 708-709 room,G buliding,ZhiGu Technology Park,YinTian Road,Xixiang, Bao'an District, Shenzhen City
Contact name:
Shenzhen Natywish Technology Co., Ltd. |
|
|
SFP Module Transceiver GPON class B+ / OLT SFP Module Transceiver
The transceiver is a high performance module for single fiber communications using a 1310nm burst-mode transmitter and a 1490nm continuous-mode receiver. It is used in the optical network terminal (ONT) for GPON ONT Class B+ applications.
The Transmitter is designed for single mode fiber and operates at a nominal wavelength of 1310nm. The transmitter module uses a DFB laser diode with full IEC825 and CDRH class 1 eye safety. It contains APC functions, a temperature compensation circuit to ensure compliance with G.984.2 requirement at operating temperature, LVPECL data inputs and DC coupling circuit.
The receiver section uses a hermetic packaged APD TIA (APD with trans-impedance amplifier) and a limiting amplifier. The APD converts optical power into electrical current and the current is transformed to voltage by the trans-impedance amplifier. The differential DATA and /DATA CML data signals are produced by the limiting amplifier. The APD TIA is AC coupled to the limiting amplifier through a low pass filter. As the optical input power decreases, the Signal Detect will switch from high to low (de-assert point). As the optical input power is increases, Signal Detect will switch back from low to high (assert point). The assert level is at least 0.5 dB higher than the de-assert level (Signal Detect Hysteresis).
Product Features
Support ITU-T G.984.2 GPON OLT B+ application
Single fiber bi-directional data links with symmetric 2.488Gbps Tx
and 1.244Gbps Rx
1490nm continuous-mode transmitter with DFB LD
1310nm burst-mode receiver with APD-TIA
2-wire interface for integrated digital diagnostic Monitoring
Receiver RESET, Signal Detect, RSSI function indication (RESET,
RX_SD, RSSI)
SFP package with SC/UPC receptacle optical interface
Single +3.3V power supply
Operation case temperature -40~85°C for industrial and 0~70°C for
commercial
RoHS6 compliance
Applications:
Data services
Voice services
Video services
Monitoring service
FTTH
Operating Condition
| Parameter | Unit | Min. | Typical | Max. |
| Storage Temperature | °C | -40 | 85 | |
| Operating Case Temp for C-temp | °C | 0 | 70 | |
| Operating Case Temp for I-temp | °C | -40 | 85 | |
| Operating Relative Humidity | % | 5 | 95 | |
| Power Supply Voltage | V | 3.15 | 3.3 | 3.45 |
| Supply Current | mA | 500 | ||
| Bit Rate for Tx | Gbps | 2.488 | ||
| Bit Rate for Rx | Gbps | 1.244 | ||
Characteristics
All performance is specified at whole working temperature and
conditions
| Parameter | Unit | Min. | Typical | Max. |
| Transmitter | ||||
| TX Central Wavelength | nm | 1480 | 1490 | 1500 |
| Spectral Width (-20dB) | nm | 1 | ||
| Side Mode Suppression Ratio (SMSR) | dB | 30 | ||
| Mean Launched Power | dBm | 1.5 | 5 | |
| Mean Launched Power (TX Off) | dBm | -45 | ||
| Extinction Ratio | dB | 8.2 | ||
| Optical Return Loss Tolerance | dB | -12 | ||
| Transmitter and dispersion Penalty | dB | 1 | ||
| Transmitter Mask(PRBS223-1@2.488G) | Compliant With ITU-T G.984.2 | |||
| Receiver | ||||
| Receive Wavelength | nm | 1290 | 1310 | 1330 |
Sensitivity | dBm | -28 | ||
Overload | dBm | -8 | ||
| Receiver Burst Mode Dynamic Range | dB | 15 | ||
| Damage Threshold for Receiver | dBm | 5 | ||
| SD Assert Level | dBm | -30 | ||
| SD De-assert Level | dBm | -45 | ||
| SD Hysteresis | dB | 0.5 | 6 | |
| WDM Filter isolation to 1550nm | dB | 38 | ||
| WDM Filter isolation to 1650nm | dB | 35 | ||
| Electrical Interface Characteristics | ||||
| Data Input Swing Differential/TX | mV | 200 | - | 2000 |
| Data Output Swing Differential/RX | mV | 400 | 1600 | |
| Date Differential Impedance | Ω | 90 | 100 | 110 |
| LVTTL Output High | V | 2.4 | Vcc | |
| LVTTL Output Low | V | 0 | 0.4 | |
| LVTTL Input High | V | 2.0 | Vcc+0.3 | |
| LVTTL Input Low | V | 0 | 0.8 | |
| Timing Characteristics | ||||
| Guard Time (Tg) | ns | 25.6 | ||
| Reset Pulse Width (Tr) | ns | 12.8 | ||
| Reset Delay (Trd) | ns | 12.8 | ||
| Receiver Preamble Time (Tp) | ns | 140 | ||
| SD Assert Time (TSDA) | ns | 100 | ||
| SD De-assert Time (TSDD) | ns | 12.8 | ||
| RSSI Trigger Delay (Ttd) | ns | 25 | ||
| RSSI Trigger Pulse Width (Tw) | ns | 500 | ||
| Internal I2C Delay (Twait) | us | 500 | ||
