Active Member
|
[China]
Address: Room 906,Fuhai Wenchuang Park,Baoan District,Shenzhen,Guangdong Province,China
Contact name:Benson
Guangdong Morui Environmental Technology Co.,Ltd. |
|
|
Spiral Wound Ultrafiltration Membrane UPVC / Organic Glass Housing Material
Application
1. Recycle of iindustrial wastewater(papermaking wastewater,printing and dying wastewater,petrochemical wastewater,steel and iron wastewater,chemical insudtry wastewater).
2. Pretreatment for NF and RO in landfill leachate treatment;
3. Electrophoretic paint treatment; liquid concentration, separation, clarification and filtration
Features
1. The membrane silk is made of PP (polypropylene). With our unique technology, the fiber is modified and enhanced to have high strength and high toughness, so that it can work under a variety of bad conditions;
2. Outer and inner diameter of the membrane silk are 500 and 400um.It is so thin that we can install more silks (about 60 ) to 72 thousand pieces, and the total membrane area is about 60m2) into a UF shell, and suspended solids in the water can quickly plug the cross section even when the silk is broken;
3. The filtration mode is out to in, the water to be treated can flow into the membrane module from either side of it, makingthe worry about wrong installation not necessary. And because of this filtration mode, the pore on the surfaceof membrane silk can shrink during filtering, so it can have a higher filtering precision. And the pore will expand during backwashing, so it can wash away some big particles to clean the membrane at the most. All of these make our product act perfect in working process;
4. Our enhanced modified PP material has great fouling resistant ability, and it can recover its performance by backwash instead of chemical cleaning. It can reduce the damage to the membrane silk and save the cost on chemicals;
The shell is made of UPVC.
Specification
inflow (L/min) |
303 |
material |
PVDF |
operating pressure(Mpa) |
0.05-0.6 |
membrane area(m2) |
30 |
highest inflow pressure(Mpa) |
0.8 |
operating temperature |
45 ℃ |
PH range |
2-11 |
Virus removal rate(log) |
6 |
Application Conditions of Ultrafiltration membrane UF module
| Pre - filtration | 50-150 um |
| Max turbidity of inlet water | ≤ 15 NTU |
| Running mode | Cross-flow filtration or dead end filtration |
| Max inlet water pressure | 0.45 MPa |
| Max pressure difference of transmembrane | 0.2 MPa |
| Applicable PH range | 2- 12 |
| Tolerable continuous residual chlorine | 100 PPm |
| Tolerable interval residual chlorine | 200 PPm |
Backwashing Design of Ultrafiltration membrane UF module
| Backwashing pressure | 0.25 MPa |
| Backwashing frequency | Every 20 -60 minutes |
| Backwashing time | 30-60 seconds every time |
| Frequency of chemically enhanced ( CEB ) | Auto adding of additives in backwashing is recommended. |
| Time of chemically enhanced backwashing ( CEB ) | 30- 60 seconds every time |
Chemically washing design of Ultrafiltration membrane UF module
| Frequency of chemically washing | Every 1~4 months or when TMP is over 0.15 MPa |
| Pressure of chemically washing | 0.15 MPa |
| Time of chemically washing | 60 -minutes every time |
| Acid washing chemical | Citric acid or oxalic acid ( mixed into solution with PH = 2 ) |
| Alkali washing chemical | NaOH ( mixed into solution with PH=2) |
Index of output water of Ultrafiltration membrane UF module
| Turbidity of output water | < 0.1 NTU |
| Index of silt density | < 1.5 |
| Microorganism, pathogen | 99.9 % Removed |
| Remarks: | 1. Pure water flux is measured with pure water at the pressure of 0.1MPa. 2. If water are from surface water ,river water or well water and so on ,pre-treatment shall be done. It is suggested that a 50-150 um precision filter shall be equipped to have inlet water with turbidity ≤15NTU. |
Compared with other systems in this field, it has a lot of
advantages as follows:
1. With ingenious and compact design, it takes up a small area and
has a high automatic performance.
2. Clean and clear filtration water without the problems of olid
smell and getting turbid.
3. Adopting automatic control system, including automatic
back-washing, needing no one on duty, saving labor cost, solving
the problem effectively of the traditional equipments' complicated
operation and invalidation due to the operating or protecting
improperly.
4. Stable performance, long life time, low running cost.
5. Environment friendly, no second pollution.
6. More than 90% water reuse rate, no natural wastage...
Morui Environmental Technology Co., Ltd. is specializing in high-tech enterprises ultrafiltration membrane and reverse osmosis membranes research and development, production, sales and services. The company has advanced core ultrafiltration technology. Combined with nearly 20 years of production experience, PES, PS, PVDF, PAN, PVC and other membrane materials were successfully modified composite, and produce high-quality ultrafiltration membrane series products. Our products have been recognized by many customers at home and abroad in the water treatment industry.
Excellent quality and large-scale production bring cost-effective ultrafiltration membrane products, not only create tremendous business opportunities, but also for humanity and make greater contribution to the cause of environmental protection.
