Haiyan Hager Fastener Co., Ltd. |
Verified Suppliers
|
|
Stud Bar ASTM A320 Grade L7 L7M L43 "End to End" Class 2A
The mechanical performance of the product shall meet the following standards, with specifications greater than or equal to 2-3 / 4 inches
TENSILE STRENGTH >860/mm2
YIELD STRENGTH MIN 725/mm2
ELONGATION >16%
REDUCE >50%
TEMPERING >593℃
QUENCHING 820-990℃
HARDNESS <32HRC
CHARPY V NOTCH IMPACT VALUE (J) MINUS -101C DEGREE
All thread rod is manufactured in 3 ways: mass-produced, cut-to-length, and cut thread. Common grades and diameters are mass produced and available across the country. Cut-to-length all thread rod uses mass-produced rods which are then cut to the finished length with the ends chamfered. Cut thread all thread rod is manufactured for special grades of steel that are not mass produced. These rods are cut slightly longer than the finished length, fully threaded, then cut to the finished length and chamfered on each end. For all manufacturing styles, the all thread rod can then be galvanized or coated per the customer’s requirements
A193 MECHANICAL PROPERTIES | |||||||
Grade | Size | Tensile, ksi, min | Yield, ksi, min | Elong. % min | RA min | HBW, max | HRC, max |
B7 | up to 2-1/2" | 125 | 105 | 16 | 50 | 321 | 35 |
2-5/8" - 4" | 115 | 95 | 16 | 50 | |||
4-1/8" - 7" | 100 | 75 | 18 | 50 | |||
B8 Class 1 | all | 75 | 30 | 30 | 50 | 223 | 35 |
B8 Class 2 | up to 3/4" | 125 | 100 | 12 | 35 | 321 | 35 |
7/8" - 1" | 115 | 80 | 15 | 35 | |||
1-1/8" - 1-1/4" | 105 | 65 | 20 | 35 | |||
1-3/8" - 1-1/2" | 100 | 50 | 28 | 45 | |||
B8M Class 1 | all | 75 | 30 | 30 | 50 | 223 | 96 |
B8M Class 2 | up to 3/4" | 110 | 95 | 15 | 45 | 321 | 35 |
7/8" - 1" | 100 | 80 | 20 | 45 | |||
1-1/8" - 1-1/4" | 95 | 65 | 25 | 45 | |||
1-3/8" - 1-1/2" | 90 | 50 | 30 | 45 | |||
B16 | under 2-1/2" | 125 | 105 | 18 | 50 | 321 | 35 |
over 2-1/2" - 4" | 110 | 95 | 17 | 45 | |||
over 4" - 8" | 100 | 85 | 16 | 45 |
A193 CHEMICAL PROPERTIES | ||||
Element | Grade B7 | Grade B8 | Grade B8M | Grade B16 |
Carbon | 0.37 - 0.49% | 0.08% max | 0.08% max | 0.36 - 0.47% |
Manganese | 0.65 - 1.1% | 2.0% max | 2.0% max | 0.45 - 0.7% |
Phosphorus, max | 0.04% | 0.05% | 0.05% | 0.04% |
Sulfur, max | 0.04% | 0.03% | 0.03% | 0.04% |
Silicon | 0.15 - 0.35% | 1.0% max | 1.0% max | 0.15 - 0.35% |
Chromium | 0.75 - 1.2% | 18.0 - 20.0% | 16.0 - 18.0% | 0.8 - 1.15% |
Nickel | 8.0 - 11.0% | 10.0 - 14.0% | ||
Molybdenum | 0.15 - 0.25% | 2.0 - 3.0% | 0.5 - 0.65% | |
Vanadium | 0.25 - 0.35% | |||
Aluminum, max | 0.02% |
A193 RECOMMENDED HARDWARE | ||
Grade | Nut | Washer |
B7 | A194 Grade 2H | F436 |
B8 Class 1 | A194 Grade 8 | 304 Stainless |
B8 Class 2 | A194 Grade 8 | 304 Stainless |
B8M Class 1 | A194 Grade 8M | 316 Stainless |
B8M Class 2 | A194 Grade 8M | 316 Stainless |
B16 | A194 Grade 7 | F436 |