|
[China]
Trade Verify
Address: 101-1101, Building 17, Dianda Guyuan Industrial Park, Mashantou Community, Matan Street, Guangming District, Shenzhen
Contact name:June Zhao
Shenzhen Merrytek Technology Co., Ltd. |
|
Verified Suppliers
|
|
|
Microwave Motion Sensor MC090S U, Batch over FCC, 120-277VAC, Superior Immunity to Interference
1. Features
Eight DIP switch setting, distance, time, daylight sensor, multi-speed adjustable.
Ultra-small mounting size, multiple mounting options, support for top and bottom mounting options.
Super cost-effective, support a variety of lamps, tri-proof lamps, ceiling lamps.
The infrared sensor is used to filter out the light sensor, and the light sensitivity value is more accurate, and is not affected by cloudy and sunny days.
Low impedance 5.8G antenna for superior immunity to interference.
Batch over FCC, TUV certification.
2. Parameter
| Input | Operating Voltage Range | 120-277VAC 50/60Hz |
| Rated Voltage | 120-277VAC 50/60Hz | |
| Stand-by Power | ≤0.5W | |
| Surge Test | Between L and N: 1KV | |
| Output | Working Mode | ON/OFF |
| Type of Load | Resistive or Capacitive | |
| Load Capacity | 200W@120VAC, 400@270VAC (Capacitive) 400W@120VAC, 400@270VAC (Resistive) | |
| Current of Load | N/A | |
| Load surge current | 30A relay - 30A (test twidth 500us @230Vac at 50% Ipeak, cold start at full load) or 60A (test twidth 200us @230Vac at 50% Ipeak, cold start at full load) | |
| Sensor | Operating Frequency | 5.8 GHz ±74.9 MHz.ISM wave band |
| Transmitting power | 0.5mW Max. | |
| Hold time | 5S/30S/60S/3min/5min/10min/20min/30min | |
| DIM down | N/A | |
| Cut off | N/A | |
| Detection Area | 100% / 75% / 50% / 25% | |
| Daylight Sensor | 2Lux/10Lux/25Lux/50Lux/Disable | |
Detecting Radius (Installed at 3m high ) | Normal moving:4-6m Fast moving:2-3m
| |
| Mounting Height | 2.5-6 m(Suction Top Installation) | |
| Detecting Angle | Ceiling mount 150° | |
Operating Environment | Operating Temperature | -20℃…+60℃ Humidity: 85% (non-condensing) |
| Storage Temperature | -40℃…+80℃ | |
| Certificate Standards | Safety standards | EN61058-1, EN61058-1-2 |
| EMC standards | EN300440, EN301489-1, EN55015, EN61547, EN61000-3-2, EN61000-3-3, EN62479 | |
| Environmental Requirement | RoHS | |
| Certificate | TUV & FCC | |
| Others | Input/output terminal specifications | 0.5-0.75mm2 |
| IP Rating | IP20 | |
| Protection Class | Class II | |
| Installation | Built-in installation | |
| Dimension | 72*36*24.5mm | |
| Package | Bubble bag + partition + outer box (K=A) | |
| Net Weight | 38g | |
| Lifetime | 5 years warranty @Ta 230V full load | |
Note 1. “N/A”means not available. 2. Detection area is effected on volume of motion object and motion speed. The detection area is tested by a 165cm height person and walking speed is 0.5m/s. | ||
3. Function
On/OFF Function
4. Dimension (mm)
5.Wiring
*The sensor is designed for connect one load only. Connect more than one loads may damage the sensor.
6.Structure
7. Radiation Pattern
*50%,75%,100% detection sensitivity is workable when installed at 5.5m mounting height. Only 25% sensitivity is not able to detect motion signal.
8. Function Dialing Settings
Detection Area
| 1 | 2 | ||
| Ⅰ | ON | ON | 100% |
| Ⅱ | ON | - | 75% |
| Ⅲ | - | ON | 50% |
| Ⅳ | - | - | 25% |
| 3 | 4 | 5 | ||
| Ⅰ | ON | ON | ON | 5S |
| Ⅱ | ON | ON | - | 30S |
| Ⅲ | ON | - | ON | 1min |
| V | ON | ON | - | 3min |
| IV | - | ON | ON | 5min |
| IIV | - | ON | - | 10min |
| ⅢV | - | - | ON | 20min |
| IX | - | - | - | 30min |
Daylight Sensor
| 6 | 7 | 8 | ||
| Ⅰ | ON | ON | ON | 2Lux |
| Ⅱ | ON | ON | - | 10Lux |
| Ⅲ | - | ON | - | 25Lux |
| V | ON | - | - | 50Lux |
| IV | - | - | - | Disable |
9. Override Function
Quick switch ON/OFF 3 times within 2sec to override sensor function. Lights will switch on all the time. Power off and on again to recover sensor function.
10. Initialization
After power on, the sensor automatically turns on light at 100% brightness. After 10sec, it turns off the light. During the initialization, the sensor is not able to detect movement.
11. Factory settings
Detection Area: 100%, Hold Time: 5S, Daylight Sensor: Disable
12. Use Caution
1. Be sure to cut off the power supply before installing or adjusting the setting of the dial switch.
2. The microwave cannot pass through the metal, make sure there are no metal above the sensor.
3. It has to be at least 3.5mm away from metal around the microwave antenna. It is not allowed to place antenna and metal on the same horizontal.
