Active Member
|
[China]
Address: NO 21st ChuangXing Road, Shangsha community , Changan Town, Dongguan city Guangdong province, China
Contact name:Admin deng
Dongguan Ming Rui Ceramic Technology Co.,ltd |
|
|
Good Dielectric Strength Alumina Ceramic Rod Ceramic Electrode Pin
| Product Name | Good Dielectric Strength Blue Ceramic Rods Ceramic Electrode Pin |
| Material | Blue ceramic rod |
| Color | White, Black or Blue |
| OD | 0.2mm - 50mm, And According to drawings |
| Length | 5mm - 400mm, And According to drawings |
| Surface Roughness | Ra0.05 |
| Torlerance | +/- 0.001mm |
| Lead time: | 15 days |
| Max. working temperature | 1500 -1700 °C |
| Samples | Avaliable |
| Shipping: | Air Express (DHL/UPS/TNT/ FedEx) or Ocean Shipping |
insulation properties together with high hardness and good wear resistance,but relatively low
strength and fracture toughness.Alumina ceramics are generally white but may also be pink or
ivory.The color is derived from either the sintering additives or impurities in the raw materials.
1. High hardness Blue ceramic rod .
2. High heat resistance : Alumina ceramic has excellent thermal stability,which means that it is
widely used in areas where resistance to high temperatures is essential.
3. Good wear resistance : Blue ceramic pin is the material of choice for alumina wear parts.
4. High electrical resistivity : Alumina is an electrically insulating material.
5. High corrosion resistance : Blue ceramic rod is insoluble in water and only slightly soluble in strong acid and
alkaline solutions. Good chemical stability of alumina leads to high corrosion resistance.
Performance:
| Alumina Content | Unit | 80-85% | 90-96% | > 99.5% | 99% |
| General Application | Lower Cost Electrical & Mechanical | High Strength, Wear Resistant, Electronic, Insulating, Mechanical, Structural & Metalizing | Extremely High Purity, Temperature & Strength; Excellent Corrosion & Wear Resistance | Porous, Easily Degassed & Machinable | |
| Porosity | % | 0-.05 | 0-.05 | 0-.05 | Variable |
| Density | gm/cm3 | 3.45-3.50 | 3.55-3.75 | 3.75-3.95 | 2.4 |
| Flexural Strength | kpsi | 35.0-40.0 | 40.0-50.0 | 50.0-55.0 | - |
| Comprehensive Strength | kpsi | 260.0 | > 300.0 | > 300.0 | - |
| Tensile Strength | kpsi | 15.0-20.0 | 20.0-28.0 | 20.0-28.0 | - |
| Linear Coefficient of Thermal Expansion | (cm/cm/°C) 25-300°C 25-700°C | 5.9X10-6 6.5X10-6 | 6.3X10-6 7.0X10-6 | 6.5X10-6 7.5X10-6 | 6.5X10-67.5X10-6 |
| Dielecctric Constant at 25°C | 1 MH 10 MH | 8.5-8.9 8.4-8.8 | 9.2-9.8 9.0-9.6 | 9.5-9.9 9.3-9.7 | - |
| Dielectric Strength | Volt/mil | 200 | 225 | 225 | - |
| Te Value | °F °C | 1472 800 | > 1832 > 1000 | > 1832 > 1000 | > 1832 > 1000 |
| Thermal Conductivity at 25°C | cal/sec/cm2/cm/°C | .03-.04 | .04-.06 | .07-.08 | - |
| Safe Use Temperature | °F °C | 2550 1400 | 3000-3100 1650-17 |
Ceramic adapter plate,Ceramic centering pin,Ceramic connectors,Ceramic spinner,Ceramic roller
Ceramic blade,Ceramic brackets,Ceramic disc,Ceramic insulator,Ceramic rod,ceramic atomizer
ceramic fuse pin,ceramic nozzle,ceramic ferrule,ceramic necklace,ceramic ornament,alumina ceramic plate, ceramic cylinder, ceramic guide, ceramic pin, ceramic bushing, ceramic brick,ceramic injection molding,ceramic bushings,ceramic smoking pipe, ceramic spacer,ceramic piston pump,ceramic part
ceramic heating element vaporizer e cigarette, al2o3 ceramic, ceramic donut atomizer, alumina ceramic disc, alumina ceramic sheet , ceramic alumina , ceramic pressure sensor , ceramic sheet,
ceramic washer, zirconia ceramic plate, ceramic insert, white ceramic ring, ceramic shaft
ceramic pump, ceramic piston, ceramic nail, ceramic insulators, ceramic rod 3mm , ceramic dowel pin
ceramic pin gage , alumina ceramic parts , ceramic burr , ceramic proppant , ceramic needle
ceramic grinder, alumina ceramic rod , alumina ceramic ring, ceramic conical burr , ceramic heater rod
ceramic gear , machinable ceramic, ceramic arms , white ceramic ornaments , sustained high temperature on ceramics
Mingrui offers you a wide range of production facilities like extrusion, injection moulding, pressing and casting. Depending on product geometry and quantities, we will choose the suitable technique for your products.For the final finishing of the parts we use CNC machining centres, equipped with diamond tools in order to meet high accuracies.
Our aim is to offer the ideal solution for any application. Our engineers therefore offer custom solutions that range beyond our existing product portfolio. With our well-equipped industrial development facilities, we produce innovations that can be rapidly commercially exploited.
A: We are factory.
A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock, it is according to quantity.
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.
A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 30%
T/T in advance ,balance before shippment.
If you have another question, pls feel free to contact us as below:
