|
[China]
Trade Verify
Address: Dongbao Industrial Park, Number 151, Jiangshi Road, Gongming, Bao'an District, Shenzhen 518106.
Contact name:AGsonic
AG Sonic Technology limited |
|
Verified Suppliers
|
|
|
38L 40KHZ Electronic Assembly Cleaning Electronic Board Ultrasonic
Machine
How an ultrasonic cleaner works to clean Medical Device
special solvents designed for cleaning Electronic Board can be
utilized however very good results can also be obtained by using
water and an environment friendly low pH cleaning agent. Low pH or
excessively high pH chemicals should be avoided. These aggressive
chemistries in combination with heat and the ultrasonic activity
can potentially cause damage to delicate pieces.
In the cleaning process, Electronic Board are submerged in the
cleaning solvent. The intensity of the cleaner as well as the heat
of the solution should be adjusted to successfully engage the
application. Ultrasonic cleaners work quickly to completely remove
dirt and other contamination through a cavitation process.
Electronic Board is cleaned in the same way as other items.
Electronic Board are submerged into a gentle solvent and the
cleaning process sends ultrasonic waves through the solution which
creates bubbles that clear away all dirt and grime clinging to the
jewelry’s surface. In most cases a short two to three minute
cleaning is all that is required for optimum results.
Benefits of cleaning Electronic Board with an ultrasonic cleaner
• The process reaches parts of the Medical Device that are
extremely difficult to clean with traditional cleaning methods.
Medical Device gets completely clean, leaving it looking brand new.
• No need to disassemble the jewelry.
• Multiple pieces can be cleaned at once, saving time and money.
Follow manufacturer recommendations for maximum pieces in your
ultrasonic cleaner.
• Gentle cleaning does not damage delicate pieces and allows for
cleaning as often as necessary.
Steps to cleaning Electronic Board with an ultrasonic cleaner
1. Fill chamber with cleaning solvent
2. Note that water must be hot. Ideally, you would use an
ultrasonic cleaner with a heater.
3. Run a pre-cleaning cycle
4. Submerge Medical Device into cleaning solvent
5. Run the cleaning cycle
6. After the cycle is complete, remove the items from the parts
basket and rinse the solution from the items
7. After rinsing brush the pieces with a soft-bristled brush.
Paying special attention to brushing around the claws and crowns
that hold the gemstones or diamonds in place.
8. Complete with a final rinse. Place the jewelry in w
Applications:
| Industry | Items to clean |
| Moulds | Plastic tool models --For cleaning. |
| Electronics | Relay—remove metal filings and impurities, Potentiometer-- impurities and oil stain on moving contact, Vacuum tube parts-- Dirt and impurity on the polar plate of electron gun, Semiconductor element--Dir on the surface of silicon wafer and crystal wafer, Capacitor--Dirt on pins of capacitor, Printed circuit board--Ink and oxide left during processing printed circuit board, Magnetic head--Dirt on the surface of the magnetic head. |
| Mechanical | Bearing, gear--Metal filings and impurities left during the processing of internal and external sheath of bearing, Spring--cleaning before spring turning black, Vernier caliper, measuring tool--Metal filings and oil stain left during the processing of parts, Oil choke, oil pump--Metal filings and dirt left during the process of inner hole of oil choke and oil pump, Screw rod, air valve, pneumatic elements--Iron filings, cutting oil and abrasive left while processing. |
Automotive, motorcycle, aircraft | To remove oil, grease, preservative, plastic residue left during mechanical cutting, grinding abrasive, glass fiber, dust, graphite and tar from Automotive air valve, glow plug, gasification plug, fuel pump, piston ring, battery terminal, machine control hand-wheel, motorcycleair-valve,etc. |
| Armurerie | weapons cleaning, such as guns, rifle, bullets , handcuffs, etc. --For cleaning and lubrication. |
| Printing industry | Rotative machine, metal plate, Printer ink head, printer cartridges -- To clean ink, oil and dye on the surface of printing machine & parts. |
| Repair industry | Musical instrument repair shop, vehicle maintenance shops, motorcycle repair shop, mobile phones & interphone repair shop, gun repair shop, etc. --To clean dirt, impurity and oils from surface of tools and spare parts. |
| Watch & clock | Gear wheel, pin, screw, movement of watches for watch manufacture, repair shops, Watch collectors, etc. --For cleaning. |
Model: AG-120ST details:
| Model | T-12S (digital timer&heater, Power adjustable) |
| Capacity | 38liter |
| Tank size | 500×300×250mm (LxWxH) |
| Unit size | 640×440×470cm (LxWxH) |
| Packaging size | 740x540x570mm (wooden case) |
| Ultrasonic power | 240~600W adjustable |
| Heating power | 1500W |
| Timer | 1~99mins adjustable |
| Heater | 20~80C adjustable |
| Frequency | 40,000Hz |
| Power supply | AC110~130V, AC 220~240V, 50/60 Hz |
| Tank material | SUS304, 2mm thickness |
| Shell Material | SUS304, 1mm thickness |
| Others | With drainage, basket, lid |
| N.W./ G.W. | 51KG/ 72KG |
| Warranty | 1 year& tech support for life |
Features:
Ultrasonic Cleaner for Car Parts / Fuel Injector Cleaning Production :
