|
[China]
Trade Verify
Address: 23E BlockB,Lushan Building，Chunfeng Road,Luohu District,Shenzhen,518001,China
Contact name:Eva
Shenzhen Wisdomlong Technology CO.,LTD |
|
Verified Suppliers
|
|
|
The IC660BBD024 is a 12/24 VDC 32-Circuit Source I/O Block that
sends current to field output devices. This block is an intelligent, configurable module that interfaces
the controller to devices that send or receive a binary signal. The
IC660BBD024 works with electronic proximity switches in 2-wire and
3-wire configurations, as well as a number of other input devices.
The IC660BBD024 block’s 32 identical discrete circuits can be set as input, output, or output with feedback. Block circuits are self-protecting. When a circuit is used as an output, block software protects its driver and guards against shorted electrical loads caused by wiring errors. In the interest of block operation, circuit protection also allows for short-duration surges.
Like other products in this class of electronics, block configuration is done with a handheld monitor. If a handheld monitor is not available, the user may choose to configure the block by sending a Write Configuration datagram from the host to the block. Block calibration is not necessary as it is performed by the manufacturer. Configuration, however, is performed by the user.
Genius I/O Source Blocks, including the IC660BBD024, provide current to field output devices but can function as a Bus Switching Module (BSM) controller. If needed, the user can replace the electronics assembly in this block without reconfiguring the block or removing field wiring if the replacement assembly is from a compatible block model. Like other blocks in the Genius I/O family, the IC660BBD024 should be installed within a protective enclosure. It can be mounted right-side up or upside down.
| Rated Voltage: | 12/24 VDC |
| # of Points: | 32 |
| Input Range: | 18-30 VDC |
| Load Current: | 0.5 |
| Operating Voltage: | 10-30 VDC |
| Points per Common: | One group of 32 |
Block Type: CatalogNumbers: 32 Circuit 12 / 24 VDC Source:I / OBlock TerminalAssembly ElectronicsAssembly 32Circuit5 / 12 / 24VDCTTLSink: I / OBlock TerminalAssembly ElectronicsAssembly | DC 32-circuit discrete input and output IC660BBD024 IC660TBD024 IC660EBD024 IC660BBD025 IC660TBD025 IC660EBD025 |
Size (height x width x depth): Weight LEDs (I/O Block) LEDs (each circuit) Block to Block Isolation HeatDissipation | 8.83” (22.44cm) x 3.56” (9.05cm) x 4.42” (11.23cm) 4 lbs. (1.8 kg) Unit OK, I / OEnabled Individual logic side indicators 850V
11W minimum with 8 inputs 18W maximum with 32 outputs at .5 amp |
Operating voltage (single source)
Ripple(maximum) Required DC power Power supply dropout times | 10 to 30 VDC (12 / 24 V supply) 4.9 to 5.3 VDC (5 V supply) (sink model only) absolute instantaneous limit 10% (12 / 24 volts) , 1% (5 volts) 150 mA typical, 300 mA maximum 4 mS at 12 volts, 20 ms at 24 volts |
Input Characteristics: Input voltage relative to (DC–) Input ON,5 VDC supply 12 VDC supply 24 VDC supply Input OFF5 VDC supply 12 VDC supply 24 VDC supply Input impedance (typical) Input processing time (typical) Selectable input filter times |
Source BlocksSinkBlocks not applicable0–0.8 VDC 8–12 VDC0–4 VDC 18–24 VDC0–6 VDC not applicable2–5 VDC 0–6 VDC6–12 VDC 0–12 VDC12–24 VDC 3.3 K ohms 1.4 mS (plus selectable filter delay) 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, or 100mS |
OutputCharacteristics: Maximum output current (steady state) Maximum inrush current Block output current (total) Output OFF leakage current (maximum) Output turn–on delay (maximum) Output voltage drop Output Diagnostics |
0.5 amps per circuit 4 amps up to 10 mS (once every .5 sec. maximum) 16 amps 10ïA 0.5 mS 2.0 volts maximum at 4 amps inrush Switch Fault |
Environmental: Operating temperature Storage temperature Humidity Vibration |
0 C to +60 C (+32 to +140 F) –40 to +100 C (–40 to +212 F) 5% to 95% (non–condensing) 5–10Hz 0.2” (5.08mm) displacement, 10–200Hz at 1G |
