GE FANUC IC693MDL751 90-30 Series Programmable Logic Controllers

GE FANUC IC693MDL751 , Output Module , 90-30 Series Of Programmable Logic Controllers

Product Description

The IC693MDL751 output module is manufactured by GE Fanuc and belongs to the 90-30 series of Programmable Logic Controllers. The module consists of 32 outputs in groups of 4. This therefore implies that each group has 8 outputs. It has a voltage rating of 12/24V DC and delivers between 12 to 24 V DC and a maximum current of 0.3 Amps per point. The output device is connected between the negative power bus and the module output. The output properties of the module are compatible with a wide range of load devices including solenoids, indicators and motor starters. The characteristics include output voltage of 0.24 V maximum, off stage leakage of 0.1 mA maximum and finally a maximum ON & OFF response time of 2 ms. It’s worth noting that power for operation of field devices must be supplied by the user. A 50-pin connector is used to make connections between output circuits and the user’s output devices.

The IC693MDL751 output module is installable on any Input / Output slot of a 5 or 10-slot baseplate in the 90-30 Series PLC. The two options for field writing are the direct method or using a Weidmuller terminal block. Direct method makes use of cables that bear a female connector on the module end and have stripped or tinned wires on the other opposite end. You can fabricate or build your own cable. Alternatively, a pre- wired can be procured with either catalog number IC693CBL308 with a length of 3 feet, the equivalent of 1 meter or number IC693CBL309 which is twice the length (6 feet / 2 meters). On the other hand, a Weidmuller terminal block #912263 can be used with a GE Fanuc pre-wired cable. Ge Fanuc cables no. C693CBL306 with a length of 3 feet, (1meter) or IC693CBL307 with a length of 6 feet (2 meters) have connectors on each end. These connections join the connector module to a connector on the Din rail which is mounted on the Weidmuller terminal block.

About IC693MDL751

The GE Fanuc IC693MDL751 positive logic output module is a 12/24 Volts DC rated positive logic output module with 32 output points. A 50-pin male Honda connector located on the front of module connects the module outputs to user devices. Wiring to field devices can be made either through the direct method which uses cables with a mating female connector on the module end and tinned wires on the device end or through terminal blocks. For the terminal block method, a 3-foot cable and a 6-foot cable are available for connecting the 50-pin module connector to a DIN-rail-mounted terminal block assembly. These extension cables are wired pin-to-pin. GE Fanuc recommends the use of terminal blocks for connecting field wiring to the 50-pin I/O modules. The use of a connector interface provides a convenient method for terminating the field wiring on the modules.

The IC693MDL751 positive logic output module can be used with the GE Fanuc Series 90-30 PLCs. It provides 4 groups of 8 output points each. The output voltage range is 12 to 24 Volts DC (+20%, 15%). The current drawn by the IC693MDL751 positive logic output module is 21 milliamps when all the outputs are on. The "per output" and "per common" peak current output ratings are 0.3 Amps and 2 Amps, respectively. Up to 1500 Volts of isolation is available between the logic and field sides of the module. The off-state leakage and output voltage drop ratings for the IC693MDL751 positive logic output module are 0.1 milliamps and 0.24 Volts DC, respectively. The IC693MDL751 positive logic output module has positive logic characteristics. The IC693MDL751 positive logic output module is connected between the module output and the negative power bus. Indicators and solenoids are some of the devices which can be used with the IC693MDL751 positive logic output module.

Technical Specifications

Technical Information