EP2C8T144I8N Intel Altera FPGA IC LFBGA Field Programmable Gate Array EP2C8 Cyclone II Device

EP2C8T144I8N Intel Altera FPGA IC LFBGA Field Programmable Gate Array EP2C8 Cyclone II Device

EP2C8T144I8N Intel Altera FPGA IC LFBGA Field Programmable Gate Array EP2C8

Intel/Altera series Field Programmable Gate Array (FPGA) IC 85 165888 8256 144-LQFP

The Cyclone II family offers devices with the Fast-On feature, which offers a faster power-on-reset (POR) time. Devices that support the Fast-On feature are designated with an “A” in the device ordering code. For example, EP2C5A, EP2C8A, EP2C15A, and EP2C20A. The EP2C5A is only available in the automotive speed grade. The EP2C8A and EP2C20A are only available in the industrial speed grade. The EP2C15A is only available with the Fast-On feature and is available in both commercial and industrial grades. The Cyclone II “A” devices are identical in feature set and functionality to the non-A devices except for support of the faster POR time.

Specification:IC FPGA 85 I/O 144TQFP Cyclone II Device

Introduce:

Altera Cyclone II FPGAs extend the low-cost FPGA density range to 68,416 logic elements (LEs) and provide up to 622 usable I/O
pins and up to 1.1 Mbits of embedded memory. Cyclone II FPGAs are manufactured on 300-mm wafers using TSMC's 90-nm low-k

dielectric process to ensure rapid availability and low cost. By minimizing silicon area, Cyclone II devices can support complex digital

systems on a single chip at a cost that rivals that of ASICs. Unlike other FPGA vendors who compromise power consumption and

performance for low-cost, Altera’s latest generation of low-cost FPGAs—Cyclone II FPGAs, offer 60% higher performance and half the

power consumption of competing 90-nm FPGAs.

The low cost and optimized feature set of Cyclone II FPGAs make them ideal solutions for a wide array of automotive, consumer,
communications, video processing, test and measurement, and other end-market solutions.

Low-Cost Embedded Processing Solutions:

Cyclone II devices support the Nios II embedded processor which allows you to implement custom-fit embedded processing solutions. Cyclone II devices can also expand the peripheral set, memory, I/O, or performance of embedded processors. Single or multiple Nios II embedded processors can be designed into a Cyclone II device to provide additional co-processing power or even replace existing embedded processors in your system. Using Cyclone II and Nios II together allow for low-cost, high-performance embedded processing solutions, which allow you to extend your product's life cycle and improve time to market over standard product solutions.

Low-Cost DSP Solutions:

Use Cyclone II FPGAs alone or as DSP co-processors to improve price-to-performance ratios for digital signal processing (DSP) applications. 

■Up to 150 18 × 18 multipliers
■ Up to 1.1 Mbit of on-chip embedded memory
■ High-speed interfaces to external memory
■ DSP intellectual property (IP) cores
■ DSP Builder interface to The Mathworks Simulink and Matlab design environment
■ DSP Development Kit, Cyclone II Edition

Cyclone II devices include a powerful FPGA feature set optimized for low-cost applications including a wide range of density, memory, embedded multiplier, and packaging options. Cyclone II devices support a wide range of common external memory interfaces and I/O protocols required in low-cost applications. Parameterizable IP cores from Altera and partners make using Cyclone II interfaces and protocols fast and easy.

Features:

● 133-MHz PCI-X 1.0 specification compatibility
● High-speed external memory support, including DDR, DDR2,and SDR SDRAM, and QDRII SRAM supported by drop in
Altera IP MegaCore functions for ease of use
● Three dedicated registers per I/O element (IOE): one input register, one output register, and one output-enable register
● Programmable bus-hold feature
● Programmable output drive strength feature
● Programmable delays from the pin to the IOE or logic array
● I/O bank grouping for unique VCCIO and/or VREF bank settings
● MultiVolt™ I/O standard support for 1.5-, 1.8-, 2.5-, and 3.3-interfaces
● Hot-socketing operation support
● Tri-state with weak pull-up on I/O pins before and during configuration
● Programmable open-drain outputs
● Series on-chip termination support
■ Flexible clock management circuitry
● Hierarchical clock network for up to 402.5-MHz performance
● Up to four PLLs per device provide clock multiplication and division, phase shifting, programmable duty cycle, and external
clock outputs, allowing system-level clock management and skew control
● Up to 16 global clock lines in the global clock network that drive throughout the entire device
■ Device configuration
● Fast serial configuration allows configuration times less than 100 ms
● Decompression feature allows for smaller programming file storage and faster configuration times
● Supports multiple configuration modes: active serial, passive serial, and JTAG-based configuration
● Supports configuration through low-cost serial configuration devices
● Device configuration supports multiple voltages (either 3.3, 2.5, or 1.8 V)
■ Intellectual property
● Altera megafunction and Altera MegaCore function support,and Altera Megafunctions Partners Program (AMPPSM)
megafunction support, for a wide range of embedded processors, on-chip and off-chip interfaces, peripheral
functions, DSP functions, and communications functions and protocols.

Most Popular Field Programmable Gate Arrays:

About Altera (Intel)

Intel and Altera announced on June 1, 2015, that they had entered into a definitive agreement under which Intel would acquire Altera. The transaction closed December 28, 2015. The acquisition couples Intel’s leading-edge products and manufacturing process with Altera’s leading field-programmable gate array (FPGA) technology. The combination enables new classes of products that meet customer needs in the data center and Internet of Things (IoT) market segments.

Product Categories:

Integrated Circuits (ICs)
Sensors, Transducers
Computer Equipment
Kits
Development Boards, Kits, Programmers
Power Supplies - Board Mount

Intel /Altera Cyclone 10 LP Device Overview

The Intel® Intel Cyclone 10 LP FPGAs are optimized for low cost and low static power, making them ideal for high-volume and cost-sensitive applications.

Intel Cyclone 10 LP devices provide a high density sea of programmable gates, onboard resources, and general purpose I/Os.

These resources satisfies the requirements of I/O expansion and chip-to-chip interfacing.

The Intel Cyclone 10 LP architecture suits smart and connected end applications across many market segments:

• Industrial and automotive

• Broadcast, wireline, and wireless

• Compute and storage

• Medical, consumer, and smart energy