Home Companies DELI ELECTRONICS TECHNOLOGY CO.,LTD

Deep UV Sterilizer Lamp Sensor High Brightness UVC LED DL-265nm-S6868-40mW

Active Member

Contact Us

[China]

Address: RM 311 3/F LINZHAN FORTUNE BUILDING No.1 SHENHUA STREET SHENFENG ROAD LIUYUE LONGGANG AREA SHENZHEN,CHINA

Contact name:VIVI

DELI ELECTRONICS TECHNOLOGY CO.,LTD

Deep UV Sterilizer Lamp Sensor High Brightness UVC LED DL-265nm-S6868-40mW

Country/Region	china
City & Province	shenzhen guangdong

Product Details

Deep UV sensor UVC-LED-265NM-6868-40mW DL-265-S68

1.Parameter:

Number:	DL-265-S68
Type:	UVC-265NM-6868
Specifications:	265NM
Driving current:	200mA
Colour:	Gold
Radiated power:	40-60mW
working voltage:	20.0~32V
Peak Wavelength:	262~274nM

2. Limitation use conditions:

Project	Unit	Range
Working temperature	℃	﹣30~60
Storage temperature	℃	﹣30~60
Max welding temperature	℃	240~260

Note:

It will affect the quality of the equipment,even broken if out of the limitation of the LED use confition. It is not recommended to operate over the above limits

4,Optoelectronic parameter value :

Instructions:

⑴ LED storage: suggest to sealed stock in under the temperature of 10℃-55℃,humidity of 30%-65%.In order to keep a good quality, pls use it within 1 year after the prodcution date; and use it out within 28days after open the package.

⑵ When taking or touch the LED, pls make sure to wear the gloves. Seal the package in time in orde to avoid the pin oxidation. When openning the package, need to use the weezers clamped on both sides of LED in order not to touch the face of the LED.

⑶ Installation: This process is mainly to protect the static electricity:

①Check if the grounding wire of the machine equipment is normal before production;

②Check if the static ring is normal, check static metal and human skin contact closely;

③ Check if the workerswear anti-static gloves;

④ Check if the working table is paved with electrostatic rubber cloth,

and the rubber cloth is connected to each other.

⑤ After opening the seal, it is better to use it out in 24hors,

otherwise it may cause the oxidation of the foot.

⑷ It is recommended to use low temperature solder paste for reflow,

and the temperature curve is shown in the following diagram.

① Preheating area:
The temperature speed is 1.0-3.0℃/S. If the temperature rises too fast, it is easy to cause paste mobility and component deterioration, then cause the tin explosive and phenomenon.
② Infiltrating area :
The temperature is 110-130℃, 90-100s is the most suitable. If the temperature is too low, then the solder will not melt if it is rewelded. It is recommended that the temperature rise speed is <2℃/ s.
③ The peak temperature should be set at 170-180℃.

The melting time suggests to adjust to 50-80 seconds when above 138℃
④ Temperature cooling spead is better <4℃/ s.

⑸ With the increase of current and temperature, the life of LED will decrease,

which leads to the acceleration of the attenuation of LED.

⑹ It is suggested that a grounding circuit should be used in the design of PCB. Pay special attention to the usage environment of LED: the temperature is between -30℃ to 55℃, and the humidity is between 65%. Otherwise, the LED will be broken by electrostatic and high current breakdown.

Major security tips:

This product is a deep ultraviolet LED, which will produce ultraviolet light after the correct operation of electricity. Thus it is harmful to the skin and eyes of the human body. No protective measures should be avoided directly in deep ultraviolet light. It is recommended to wear the protectective clothing, glove and glasses druring operation.