Uonel Co.Limtied |
|
The TOA board is mainly used to achieve cross-connection at the electrical layer, and to provide OTN interfaces and ESC.
For detailed functions and features, refer to Table 1.
Function and Feature | Description | ||
---|---|---|---|
Basic function | TOA converts signals as follows:
| ||
Client-side service type | FE: Ethernet service at a rate of 125 Mbit/s GE: Ethernet service at a rate of 1.25 Gbit/s. Supports GE optical signals and GE electrical signals. OTU1: OTN service at a rate of 2.67 Gbit/s STM-1/OC-3: SDH/SONET service at a rate of 155.52 Mbit/s STM-4/OC-12: SDH/SONET service at a rate of 622.08 Mbit/s STM-16/OC-48: SDH/SONET service at a rate of 2.5 Gbit/s FC100: SAN service at a rate of 1.06 Gbit/s FC200: SAN service at a rate of 2.12 Gbit/s FC400: SAN service at a rate of 4.25 Gbit/s FICON: SAN service at a rate of 1.06 Gbit/s FICON Express: SAN service at a rate of 2.12 Gbit/s FICON4G: SAN service at a rate of 4.25 Gbit/s HD-SDI: Bit-serial digital interface for high-definition television systems at a rate of 1.49 Gbit/s HD-SDIRBR: Bit-serial digital interface for high-definition television systems at a rate of 1.49/1.001 Gbit/s SDI: Serial digital interface at a rate of 270 Mbit/s 3G-SDI: Video service at a rate of 2.97 Gbit/s 3G-SDIRBR: Video service at a rate of 2.97/1.001 Gbit/s DVB-ASI: Video service at a rate of 270 Mbit/s ESCON: SAN service at a rate of 200 Mbit/s FDDI: SAN service at a rate of 125 Mbit/s NOTE: The TOA board supports GE optical signals and electrical signals. For GE electrical signal transmission, it is recommended that the board be equipped with at most two GE electrical modules to facilitate fiber routing. The TOA board supports access of SDI, HD-SDI, HD-SDIRBR, 3G-SDI, 3G-SDIRBR, and DVB-ASI electrical signals. When the board is used to accept these electrical signals, a digital video O/E converter must be used for O/E or E/O conversion and the optical module of the converter must agree with the board optical module specifications. The digital video O/E converter is a third-party device. Customers can purchase a digital video O/E converter by themselves. NOTE: The FICON4G service and the FC400 service are processed identically. For the FICON4G service, you can configure it as the FC400 service on the U2000. | ||
Cross-connect capabilities | Cross-connects a maximum of 16 channels of ODU0 signals or 8 channels of ODU1 signals through the backplane bus and cross-connect board. Cross-connects a maximum of five channels of ODUflex signals by using buses on the backplane and the cross-connect board. | ||
OTN function |
| ||
ESC function | Supported | ||
PRBS test function | Supports the PRBS function on the client side. NOTE: The PRBS function on the client side is supported only when the
client-side service type is STM-1/OC–3, STM-4/OC-12, STM-16/OC-48,
or OTU1. | ||
LPT function | This function is supported only when the TOA board receives FE or GE services on its client side. | ||
FEC coding | Supports forward error correction (FEC) on the client side that complies with ITU-T G.709, only when the service type is OTU1. | ||
Alarms and performance events monitoring |
| ||
ALS function | Supports the ALS function on the client side when client services are non-OTN services. | ||
Test frame | Supported NOTE: The board supports the Test frame function only when the Service Type is GE(GFP-T). | ||
Latency measurement | The board supports latency measurement. The bidirectional latency
at the ODUk layer between two tributary boards supporting the
latency measurement function can be measured, and the latency data
is displayed on the U2000. NOTE: This function is not supported when the client-side service type is
OTU1. | ||
IEEE 1588v2 | Supports the TC, TC+OC, BC, and OC modes when the client service is GE multiplexed using the GFP-T procedure (the service type is displayed as GE(GFP-T) on the U2000). Supports the BC and OC modes when the client-side service type is OTU1. NOTE: When receiving GE (GFP-T) services, the TX8/RX8 optical port cannot process IEEE 1588v2 clock signals. When receiving OTU1 services, the board only supports frequency synchronization using the receiving and transmitting timestamps in Sync messages of the IEEE 1588v2 protocol. It does not support frequency synchronization using the physical clock. | ||
Physical clock | When receiving GE(GFP-T) services on the client side, the board can support synchronous Ethernet processing instead of synchronous Ethernet transparent transmission. When receiving GE(TTT-GMP) services on the client side, the board can support synchronous Ethernet transparent transmission instead of synchronous Ethernet processing. In ODU1_ODU0 mode (OTU1->ODU1->ODU0), when the client-side service type is OTU1, synchronous Ethernet processing is supported but synchronous Ethernet transparent transmission is not supported. | ||
Electrical-layer ASON | Supported | ||
Protection scheme |
NOTE: When the board receives OTN services, SDH/SONET services the board supports tributary SNCP protection. When the cross-connect granularity is ODUflex, the board does not support tributary SNCP protection. ODU0 tributary SNCP protection is supported only in ODU1_ODU0 mode (OTU1->ODU1->ODU0). | ||
Ethernet service mapping mode | Supports encapsulation of GE services in GE(TTT-GMP) or GE(GFP-T). | ||
Ethernet port working mode | GE(TTT-GMP): Auto-Negotiation 1000M Full-Duplex | ||
Loopback | Channel Loopback | Inloop | Supported NOTE: The ODU0 channel loopback is supported only when port working mode
is ODU1_ODU0 mode (OTU1->ODU1->ODU0). |
Outloop | |||
Client side | Inloop | Supported | |
Outloop | |||
Protocols or standards compliance | Protocols or standards for transparent transmission (non-performance monitoring) | IEEE 802.3u IEEE 802.3z ITU-T G.707 ITU-T G.782 ITU-T G.783 GR-253-CORE Synchronous Optical Network (SONET) Transport Systems: Common Generic NCITS FIBRE CHANNEL PHYSICAL INTERFACES (FC-PI) NCITS FIBRE CHANNEL LINK SERVICES (FC-LS) NCITS FIBRE CHANNEL FRAMING AND SIGNALING-2 (FC-FS-2) NCITS FIBRE CHANNEL BACKBONE-3 (FC-BB-3) NCITS FIBRE CHANNEL SWITCH FABRIC-3 (FC-SW-3) NCITS FIBRE CHANNEL - PHYSICAL AND SIGNALING INTERFACE (FC-PH) NCITS FIBRE CHANNEL SINGLE-BYTE COMMAND CODE SETS-2 MAPPING PROTOCOL (FC-SB-2) SMPTE 292M Bit-Serial Digital Interface for High-Definition Television Systems ETSI TR 101 891 Professional Interfaces: Guidelines for the implementation and usage of the DVB Asynchronous Serial Interface (ASI) SMPTE 259M 10-Bit 4:2:2 Component and 4fsc Composite Digital Signals - Serial Digital Interface NCITS SBCON Single-Byte Command Code Sets CONnection architecture (SBCON) ANSI X3.139 Information Systems - Fiber Distributed Data Interface (FDDI) - Token Ring Media Access Control (MAC) ANSI X3.148 Information Systems - Fiber Distributed Data Interface (FDDI) - Token Ring Physical Layer Protocol (PHY) ANSI X3.166 Information Systems - Fiber Distributed Data Interface (FDDI) Physical Layer Medium Dependent (PDM) | |
Protocols or standards for service processing (performance monitoring) | ITU-T G.805 ITU-T G.806 ITU-T G.709 ITU-T G.872 ITU-T G.7710 ITU-T G.798 ITU-T G.874 ITU-T M.3100 ITU-T G.874.1 ITU-T G.875 ITU-T G.808.1 ITU-T G.841 ITU-T G.8201 ITU-T G.873.1 ITU-T G.694.1 |
Specifications include optical specifications, dimensions, weight, and power consumption.
Board | Client-Side Fixed Optical Module | Client-Side Pluggable Optical Module |
---|---|---|
TN54TOA | N/A | I-16-2 km-eSFP S-16.1-15 km-eSFP L-16.1-40 km-eSFP L-16.2-80 km-eSFP 1000 BASE-BX10-U-eSFP 1000 BASE-BX10-D-eSFP 1000 BASE-BX-U-eSFP 1000 BASE-BX-D-eSFP 2.125 Gbit/s Multirate-0.5 km-eSFP 1000 BASE-LX-10 km-eSFP 1000 BASE-LX-40 km-eSFP 1000 BASE-ZX-80 km-eSFP 1.25 Gbit/s Multirate (CWDM)-40 km-eSFP 2.67 Gbit/s Multirate (CWDM)-80 km-eSFP 2.67 Gbit/s Multirate (DWDM)-120 km-eSFP 0.1 Gbit/s to 3 Gbit/s Multirate 10 km-Video eSFP 4.25 Gbit/s Multirate-0.3 km-eSFP 4.25 Gbit/s Multirate-10 km-eSFP |
Board | Typical Power Consumption (W) | Maximum Power Consumptiona (W) |
---|---|---|
TN54TOA | 23 | 25 |
a: The maximum power consumption is the power consumed by the board when it works normally under the highest ambient temperature. |
Cargo will be delivered within 1 day after payment arrived. Tracking Number will be offered once delivery done.
Delivery Options | Estimated Delivery Time |
---|---|
DHL | 3-5 business days |
Fedex | 3-5 business days |
By Sea | 10-20 business days |
Notice:
Above mentioned information are just for your reference only,we will keep you posted for the tracking delivery schedule.There are two delivery options available for by air and by sea:
Deliver to port:
Uonel is responsible for transporting goods to port. All
subsequent customs and transportation fees are the
responsibility of the buyer. Uonel will recommend trustworthy
local freight forwarders to you.Uonel can facilitate the progress
under buyer's permission and at buyer's expense.
Deliver to door:
Uonel will quote all destination charge prior once we have
confirmed order.
Uonel is responsible for transporting goods to door after you
have made the payment.
100% Low Price Guarantee:
Uonel provides
high-quality products at low wholesale prices
100% Quality Assurance:
All items are
ORIGINAL NEW and GENUINE only.
Free Technical Support:
Our FREE Expert Consultancy Support is over the phone, by chat, by email or by login remotely.
100% Money Back Guarantee:
You can contact our customer service team to exchange or return any
product that you bought from us.
Flexible Secure Payment & Shipment:
Verified
authorization: Mcafee Secure, VeriSign Secured
Return Material Authorization (RMA) Process
Standard Hardware Warranty Policy:
Original new sealed product: 1 Year
The Support Contacts:
If your products failed, you must contact your sales representative to verify product failure. If the problem still can't correct by remote support methods i.e. email or phone support, the RMA procedure will issue.
Uonel is one of the biggest Network Hardware distributor in china, founded in 2008. We are a global provider of netwotking products with more than 5000 customers.
We provide original new Routers,Switches,Firewalls,Wireless APs & controllers,OLTs,GPON modems,optical transceivers.Our company have more than $5million products in stock.
Most of our technical engineers had work exprience in company,we can provide network design&planning,configration,troubleshooting,maintenance and training service in world wide.