Home Companies Nanjing Saiko Controls Co.Ltd

White 86*90*43mm Heated Floor Thermostat Temperature Controller For Warm Floor And Water Heating System

Nanjing Saiko Controls Co.Ltd
Active Member

Contact Us

[China] country

Address: No.40 Ailing Road, Moling Street, Jiangning District, Nanjing

Contact name:James Zhang

Inquir Now

Nanjing Saiko Controls Co.Ltd

White 86*90*43mm Heated Floor Thermostat Temperature Controller For Warm Floor And Water Heating System

Country/Region china
City & Province nanjing jiangsu
Categories Bricks
InquireNow

Product Details

Instruction:


   Weekly circulation digital programming thermostatwith LCD screen,which has 6-event everyday.Manual mode and programme mode could be selec-ted.The thermostat is recommended for control ofelectric heating devices or on/off valve actuator usedin hydronic floor heating.

 

Parameters:
 

Voltage220V/230V
Power consumption2W
Housing materialSelf-extinguishing
Setting range5~90ºC
Protective housingIP20

 

Dimension:

 

Display:

Sensor failure:

 

 E0:Built-in sensor short-circuited or disconnected.

 E1:Built-in sensor short-circuited or disconnected.

 When shows E0/E1 error,thermostat must be checked till thr error is eliminated.

 

Selection:

ModelCurrentApplication
SK5133ABuilt-in&floor sensor,floor limit sensor weekly programme
SK5233ABuilt-in&floor sensor,floor limit sensor weekly programme,a potential free output
SK5016ABuilt-in&floor sensor,floor limit sensor weekly programme

 

Wiring diagram:

More products for you to choose:

 

FAQ

 

1.How long will it take for the underfloor heating system to warm up?

   The warm up time of an electric underfloor heating system will be dictated by the insulation used beneath it and the output of the system. In general, the better insulated the sub-floor the faster the system will warm up, with Underfloor Insulation boards?facilitating a very speedy warm up time of as little as 15 minutes, and un-insulated concrete floors causing the slowest warm up time. Using a?200W system?beneath ceramic/stone tiles provides a faster warm up time than 150W system.

 

2. Can I turn my heating on the day it is fitted?

   If you have installed your heating beneath tile adhesive, levelling compound or a screed you must allow this to dry out before turning on your system for the first time. If the system is turned on too early it will force the moisture out of the covering which may lead it to crack. We would recommend speaking to the manufacturer of your flexible tile adhesive, grout or screed to confirm the drying time required.

 

3. Does each room require its own thermostat?

   We would recommend that each room has its own heating system controlled by its own thermostat. This will allow for simpler and more accurate temperature control of each room and will avoid heating rooms which do not require it.
 
 

Install 

  • 1,Open main control panel, with 3.5mm slotted point screwdriver along the inclined plane until to card depths of 4mm, pry up slightly to open the card hook
  • 2,Connect back panel and power, wire as per wiring diagram, fasten back panel on cassette with M4 screw
  • 3,Connect winding displacement of back panel and upper panel
  • 4,Hang up with 30° to 2 hooks, press on the 2 bottom corners, stuck on the upper shell, installation finished. 
 

 

Hot Products

Information: SK50 series digital temperature controller is suitable for the floor heating, water ...
Information: Weekly circulation digital programming thermostatwith LCD screen,which has 6-event ...
Instruction: Weekly circulation digital programming thermostatwith LCD screen,which has 6-event ...
Instruction: Weekly circulation digital programming thermostatwith LCD screen,which has 6-event ...
Application: Weekly Programming Thermostat with LCD Screen, it is possible to set 6 perids called ...
Instruction: Weekly circulation digital programming thermostatwith LCD screen,which has 6-event ...