Active Member
|
[China]
Address: 2# Jinlong Rd. Baolong Industrial Zone, Longgang Dist. Shenzhen China 518000
Contact name:Tarik Lu
Forsentek Co., Limited |
|
|
Flange to Flange Compression Load Cell 500 ton Column Type Load Cell 300ton
Flange to flange Compression Force Sensor FCRF is made of alloy steel based on strain gauge technology adopting a column design that has a flange-to-flange mount for easy installation. High range Compression Force Transducer FCRF offers 0-300kN / 0-500kN / 0-600kN / 0-1000kN / 0-1500kN / 0-2000kN / 0-2500KN / 0-3000kN / 0-4000kN / 0-5000kN ten rated measuring ranges to choose from. You may find Cylinder Type Load Cell FCRF applicable for pile load test, bridge load monitoring, injection molding machines, structure testing, rolling mills and so on.
Dimensions(Unit in "mm")
Specifications
| Capacity | 300kN / 30 ton / 67 klb 500kN / 50ton / 112 klb 600kN / 60 ton / 135 klb 1000kN / 100 ton / 225klb 1500kN / 150 ton / 337klb 2000kN / 200ton / 450 klb 2500kN / 250 ton / 562 klb 3000kN / 300ton / 674 klb 4000kN / 400 ton / 900 klb 5000kN / 500 ton / 1120 klb |
| Rated output | 2.0 mV/V |
| Excitation | 3-15V |
| Zero balance | ±0.05mV/V |
| Nonlinearity | ±0.3% R.O. (>600kN ±0.5% of R.O.) |
| Hysteresis | ±0.3% R.O. (>600kN ±0.5% of R.O.) |
| Nonrepeatability | ±0.1% R.O. (>600kN ±0.2% of R.O.) |
| Creep(3min) | ±0.1% R.O. |
| Safe overload | 120% F.S. |
| Ultimate overload | 150% F.S. |
| Compensated temperature | -10...+40oC |
| Operating temperature | -20...+60oC |
| Temperature shift zero | ±0.02% R.O./oC |
| Temperature shift span | ±0.02% R.O./oC |
| Input resistance | 780±50 ohms |
| Output resistance | 750±50 ohms |
| Insulation resistance | >5000M ohms |
| Ingress protection | IP66 |
| Material of element | Alloy steel |
| Cable | Ø5*5000mm 4-core shielded |
| Wiring code | Red--Excitation+ Black--Excitation- Green--Signal+ White--Signal- |
A Force Sensor is a transducer that converts mechanical load into mV signal proportional to the applied force.The acting force causes deformation of the measuring element,the bonded strain gage deforms accordingly which will cause the resistance change of the wheatstone bridge,under constant power supply, the output signal between Sig+ and Sig- will change proportionally,thus the load/force can be measured by measuring the output signal from the transducer which is normaly within -30mV...+30mV.A signal amplifier can be used to convert the mV signal into 0-5V / 0-10V / 4-20mA for further signal processing.
Rated Capacity: The maximum axial load the load cell is designed to
measure within its specifications.
Non-linearity: The maximum deviation of the calibration curve from
a straight line drawn between the no-load and rated outputs;
expressed as a percentage of the rated output and measured on
increasing load only.
Non-repeatability: The maximum difference between load cell output
readings for repeated loadings under identical loading and
environmental conditions.
Hysteresis: The maximum difference between load cell output
readings for the same applied load; one reading obtained by
increasing the load from zero and the other by decreasing the load
from rated output; usually measured at half rated output and
expressed in percent of rated output.
Creep: The change in load cell output occurring with specified
period of time, while under load, and with all environmental
conditions and other variables remaining constant; usually measured
with rated load applied.
Safe Overload: The maximum load in percent of rated capacity which
can be applied without producing a permanent shift in performance
characteristics beyond those specified.
Ultimate Overload: The maximum load in percent of rated capacity
which can be applied without producing a structural failure.
Operating Temperature: The extremes of temperature within which a
load cell will operate without permanent adverse change to any of
its performance characteristics.
Temperature Shift Span: The change in output due to a change in
load cell temperature; usually expressed as a percentage of load
per degree Celsius change in temperature.
Temperature Shift Zero: The change in zero balance due to a change
in ambient temperature; usually expressed in percent of rated
output per degree Celsius change in temperature.
Input Resistance: The resistance of the load cell bridge circuit
measured at the positive and negative excitation terminals with no
load applied and with the output terminals open-circuited.
Output Resistance: The resistance of the transducer bridge circuit
measured at the positive and negative signal terminals with no load
applied and with the input terminals open-circuited.
Flange to Flange Compression Load Cell 500ton Column Type Load Cell 300 ton
