|
[China]
Trade Verify
Address: Room 2010, Building4, Jianfa Fortune Plaza, 191 Tongyi St., Qingyang District, Chengdu, China
Contact name:Liu
Sinof Hi-tech Material Co., Ltd. |
|
Verified Suppliers
|
|
|
ETFE Pellet for Molding SF-4026 with MFR 16.1-20
Product Description
Ethylene-tetrafluoroethylene, also known as ETFE, is one of the strongest fluorine plastics with good mechanical properties, weather resistance, flame retardant, gas barrier properties and chemical resistance. In addition to the similar properties like other fluorine resins, it also shows good radiation resistance, strong adhesion with metal surface, and is lighter than other fluorinated materials.
Grades
| Grade | MFR g/10min | Molding method | Application |
| SF-4021 | 0.8-2.0 | Molding | Mainly for heat shrinkable tube, lining, cable insulation. |
| SF-4022 | 2.1-4.0 | Extrusion Molding | Mainly for cable insulation and thin-walled tubes. |
| SF-4023 | 4.1-8.0 | Extrusion Molding | Mainly for cable insulation, pipes, plates, films. |
| SF-4024 | 8.1-12.0 | Extrusion Molding, Injection Molding | Mainly for cable insulation, injection molded parts, pipes, plates, films. |
| SF-4025 | 12.1-16.0 | Extrusion Molding, Injection Molding | |
| SF-4026 | 16.1-20.0 | Extrusion Molding, Injection Molding | |
| SF-4027 | 20.1-24.0 | Extrusion Molding, Injection Molding | |
| SF-4028 | ＞ 24.0 | Extrusion Molding, Injection Molding | Mainly for thin-walled sheathed wires, crosslinked cables, pipes, plates, films |
Properties
| Property | Unit | Method | SF-4021,SF-4022,SF-4023,SF-4024,SF-4025,SF-4026,SF-4027,SF-4028 |
| Appearance | - | - | Transparent pellets, without impurities such as metal shavings and sand particles. The percentage of particles containing visible black spots is less than 1%. |
| Specific Gravity | g/cm³ | ASTM D792 | 1.70-1.82 |
| Tensile Strength | MPa | ASTM D638 | ≥ 30 |
| Elongation | % | ASTM D638 | ≥ 300 |
| Flexural Modulus | MPa | ASTM D790 | 800-1000 |
| Flexural Strength | MPa | ASTM D790 | 20-30 |
| Impact Strength | Ft-lb/in | ASTM D256 | No Break |
| Hardness | °/Shore D | GB/T 2411-2008 | ≥ 50 |
| Melting Point | ℃ | DSC | 220-270 |
| Oxygen Index | % | GB/T 2406.2-2009 | ＞ 32 |
| Flammability | - | UL94 | V-0 |
| Dielectric Constant | - | ASTM D150(106) | ＜ 2.4 |
| Dielectric Loss | - | ASTM D150(106) | 0.008 |
Attention
1. When dealing with ETFE powder for deep processing, operators must wear protective cloth and mask to avoid potential safety hazards, such as inhalation of dust and toxic gas, or hurt by high temperature. No open flame and smoking in workplace. Exhaust devices should be installed.
2. When dealing with ETFE pellet for deep processing, operators must strictly control processing technic. Processing temperature should not be kept no more than 350℃. Wear protective cloth and mask to avoid potential safety hazards, such as inhalation of dust and toxic gas, or hurt by high temperature. The workplace should be tidy and ventilated.
3. Product waste must be handled properly following local laws and regulations.
Packaging, Transportation and Storage
1. Double-layered polyethylene sealed and then packed in carton. 10Kg/bag, 20Kg/carton.
2. The product should be stored in cool ventilated place and away from fire source and heat source. It should also be prevented against moisture and sunshine, kept in upright position and handled with great care.
3. Once opened, unused product should be repacked to avoid any dust or contamination.
