Results forfigure 2c test finger probefrom 7280 Products.
|
|
IEC 60335 clause 22.11 Figure 7 Test Finger Nail With 50N Built - In Force Product Overview: The test fingernail confirms to the standard of IEC60335-1 clause 21.2, clause 22.11, ...
|
|
|
|
|
IT Test Probe Ø12mm, 80mm long with tip radius 6mm Conforms to IEC60950, GB4943
|
|
|
|
|
UL1278 Fig 10.2 Bar Probe Product details: It conforms to standard requirement of UL1278 Fig 10.2. The handle is made of nylon and the probe is made of stainless steel. Standard...
|
|
|
|
|
UL6500 Figure B.1 / IEC60950-1 Figure 2C - Test Probe Telekom Sonde Purpose: Telecom-Test Probe meets IEC60950 Figure 2C and UL6500 Figure B.1 standards. is for the absolute share ...
|
|
|
|
|
IEC60529 Stainless Steel 2.5mm Test Rod for IP3 and suffix C code Test Introduction: The 2.5mm Test Rod is used to verify the protection of persons against access to hazardous ...
|
|
|
|
|
Rigid Finger 1 Ø50mm, 20mm wide, 100mm long
|
|
|
|
|
Test Rod With Nylon Handle 100mm Product information: The test probe is designed and manufactured according to the IEC 60335-2-16 clause 22.102. It is used to test concealment of ...
|
|
|
|
|
IEC60529 1.0mm Test Wire used for IP4 Code Test with Calibrated Certificate Introduction: Used to verify the protection of persons against access to hazardous parts. Also used to ...
|
|
|
|
|
UL Enamel Wire Probe 25 Usage: This probe is use to checking access to enamel coated wire accord to UL standard requirement. stainless steel with stainless stell handle.
|
|
|
|
|
UL398 Fig 8.2 Probe for Film-coated Wire Product information: This probe conforms to standard requirement of UL398 Fig 8.2(PA170B),UL507(PA170D),UL749 Fig 2,UL982 Fig 58.6 and ...
|
|
|
|
|
IP Testing Equipment Test Probe D for IP4X Testing Test Wire According to IEC60529 Introduction: Designed according to IEC61032 figure 4, meet the requirements of IEC60529-IP3...
|
|
|
|
|
IEC 60529 Test Sphere50mm , IP1X This probe is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against ...
|
|
|
|
|
IEC60335-2-14 Stainless Steel Test Probe Product information: The stirrer shall incorporate a biased-off switch that is recessed or guarded to prevent accidental operation. It ...
|
|
|
|
|
Abration Resistance Test Pin Made by Hardened Steel Conforms to IEC60950 1. Introduction The scratch resistance test uses a hardened steel pin for scratching. The end of the steel ...
|
|
|
|
|
Test Rubber Ball Usage rubber ball used for dynamic stability testing to UL (USA) standards. A ball, 2 and 3/4/16 inch diameter (2.187 inches), filled with No. 60 core sand. It is ...
|
|
|
|
|
IEC60335-2-14 Stainless Steel Test Probe Product information: The stirrer shall incorporate a biased-off switch that is recessed or guarded to prevent accidental operation. It ...
|
|
|
|
|
Antenna coaxial sockets mounted on the apparatus Antenna coaxial sockets mounted on the apparatus and incorporating parts or components which isolate HAZARDOUS LIVE parts from ...
|
|
|
|
|
IEC 60065:2014 clause 9.1.4 Test Rod Probe D HT-I04 Standard: Conforms to IEC 60065:2014 clause 9.1.4, IEC61032 figure 4 test probe D , IEC529 IPX4, IEC60065 and etc. Application: ...
|
|
|
|
|
IEC 60529 Test rod 2.5mm, IP3X Usage This wire is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against ...
|
|
|
|
|
Test Needle Diameter : Ø0.5mm or Ø1mm, Length : 20mm
|
|
|
