Active Member
|
[China]
Address: Floor 3, Building B, No. 24, Third Industrial Zone, Langxiii, Songgang Town, Baoan District, Shenzhen, Guangdong, China
Contact name:wang
Shenzhen Jiangfan Communication Equipment Co., Ltd. |
|
|
1x4 splitter Fiber Optical Box FTTH PLC Splitter box with SC 1X4 Planar waveguide type Optical splitter
Planar Optical Waveguide Splitter
PLC Splitter is a planar optical waveguide inheriting optical device based on planar optical waveguide technology. It can achieve predetermined optical power allocation in the wavelength range of 1260nm-1650nm, covering the wavelength range of 1310nm, 1490nm, and 1550nm suitable for EPON technology. Suitable for EPON passive optical network access technology hu FTTP optical network system, used for bandwidth, passive optical shunt. The characteristics of the operating wavelength range of light, virtual shunt uniformity, low loss, device reliability, good stability.
2,Model classification:
Rack TYPE PLC splitter can be divided into:
| 1*N | 1*2 | 1*4 | 1*8 | 1*16 | 1*32 |
| 2*N | 2*2 | 2*4 | 2*8 | 2*16 | 2*32 |
The connector of the product can be selected as required: FC/UPC, FC/APC, SC/UPC, SC/APC, LC/UPC, LC/APC, etc. A single box is combined with multiple boxes of optical splitter.
3,The diagram below shows the working principle of optical splitter:
Working conditions:
Working and storage temperature: -40 ℃ to +85℃
Storage relative humidity: <75%
atmospheric pressure: 76Kpa ~ 106Kpa
Number of connector insertions: >1000
Advantages Of Fiber Optic Splitter
1. Adopt high strength stainless steel, pass salt spray test
2. Ferrule core is less than 0.2um
3. Adopt 100% new raw material, ROHS compliance
4. Low Insertion loss
5. Low PDL Compact Design
6. Good channel-to-channel uniformity
7. Wide Operating Wavelength: from 1260nm to 1650nm
8. Wide Operating Temperature: from -40℃ to 85℃
5,technical parameter:
1X4 Performance parameters
| parameter | Item | index | |||||
| 1×2 | 1×4 | 1×8 | 1×16 | 1×32 | |||
| Operating bandwidth (wavelength) | nm | 1260～1650 | |||||
| Insertion loss | dB | ≤4.4 | ≤8.0 | ≤11.1 | ≤14.1 | ≤17.4 | |
| Polarization dependent loss | dB | ≤0.3 | ≤0.3 | ≤0.3 | ≤0.3 | ≤0.3 | |
| Channel uniformity | Fixed working wavelength | dB | ≤0.6 | ≤0.7 | ≤1.0 | ≤1.2 | ≤1.5 |
| full working bandwidth | dB | ≤1.1 | ≤1.2 | ≤1.5 | ≤1.7 | ≤2.0 | |
| return loss | dB | ≥50(UPC type fiber optic connector) | |||||
| directionality | dB | ≥55 | |||||
Note 1. The above are all PLC components equally divided; 2. The fiber is single-mode fiber; 3. The test wavelengths of insertion loss in the table are: 1310nm, 1490nm, 1550nm; the insertion loss in the wavelength range of 1260-1300nm and 1600-1650nm is increased by 0.3dB on the basis of the above indicators. 4. The test wavelengths of channel uniformity in the table are: 1310nm, 1490nm, 1550nm; the channel uniformity index in the wavelength range of 1260-1300nm and 1600-1650nm is increased by 0.5dB on the basis of the above index. | |||||||
2X4 performance parameters
| paramter | item | index | |||||
| 2×2 | 2×4 | 2×8 | 2×16 | 2×32 | |||
| Operating bandwidth (wavelength) | nm | 1260～1650 | |||||
| Insertion loss | dB | ≤4.6 | ≤8.2 | ≤11.4 | ≤14.4 | ≤17.7 | |
| Polarization dependent loss | dB | ≤0.3 | ≤0.3 | ≤0.3 | ≤0.3 | ≤0.3 | |
| Channel uniformity | Fixed working wavelength | dB | ≤0.6 | ≤0.7 | ≤1.0 | ≤1.2 | ≤1.5 |
| full working bandwidth | dB | ≤1.1 | ≤1.2 | ≤1.5 | ≤1.7 | ≤2.0 | |
| return loss | dB | ≥50(UPC type fiber optic connector) | |||||
| directionality | dB | ≥55 | |||||
Note 1. The above are all PLC components equally divided; 2. The fiber is single-mode fiber; 3. The test wavelengths of insertion loss in the table are: 1310nm, 1490nm, 1550nm; the insertion loss in the wavelength range of 1260-1300nm and 1600-1650nm is increased by 0.3dB on the basis of the above indicators. 4. The test wavelengths of channel uniformity in the table are: 1310nm, 1490nm, 1550nm; the channel uniformity index in the wavelength range of 1260-1300nm and 1600-1650nm is increased by 0.5dB on the basis of the above index. | |||||||
6,Product operation instructions and notes:
(1) Preparation before use:
A. Prepare anhydrous alcohol and dust-free wipe paper.
B. If possible, you can prepare a portable optical fiber magnifying glass (200 times) used in engineering.
C. Spare some models of standard test wires and standard adapters.
D. Operate with clean finger covers if conditions permit.
(2) Precautions during use:
A. After unpacking the product, check whether it is damaged.
B. Check whether the product aisle is equipped with dust protection equipment.
C. Select an optical connector based on the product model. Clean the end faces of optical connectors before leveling. When cleaning, the wiping paper dipped in alcohol should be spread flat on the desktop. When wiping, it should be wiped along the ceramic so as not to wipe the other direction from the forehead Angle. It should not be wiped back and forth to prevent damage to the end face.
D. After cleaning, separate the input and output ports, remove the dust-proof caps of the product to be used, and install the connectors. Note the following during installation:
Install the SC connector so that the key plane of the connection is consistent with the notch plane of the adapter, and then insert it horizontally along the adapter. When you hear the "click" sound, observe that the white line on the connector is flush with the adapter edge. If the card is flush, it means that the card is locked in place.
Then the input terminal and each output port are connected to the test system once to judge whether the optical indicators meet the requirements. If the connector is of other models, ensure that the connector is properly installed based on the actual model.
Package&shipping
Certification
FAQ
Q: Are you trading company or manufacturer?
A: We are original manufacturer. We can do OEM/ODM business.Our
company mainly produces optical fiber box.
Q: How long is your delivery time?
A: Group buying delivery time: 30-60 days; General delivery time: 20
days.
Q: What is your terms of payment?
A: T/T 30% as deposit, and 70% before delivery.
Q: What is the warranty ?
A: The free warranty is one year from the day of Commissioning
qualified.If there is any fault for our products within the free
warranty period, we will repair it and change the fault assembly
for free.
