Active Member
|
[China]
Address: No.377 Changbang Road, Wujiang Economic and Technological Development Zone
Contact name:Chuanchuan Li
jiangsu jzer Automation Technology Co.,Ltd. |
|
|
Introduction of Automatic N95 Mask Production Line
Function introduction
This Face Mask Manufacturing Machine is a fully automatic one-to-two mask machine, one body machine drives two ear band machines. After the main body machine outputs the mask body, the mask body sheet is conveyed to the turning mechanism by the conveyor belt structure, and the mask plate is flipped to the conveyor belt connected to the ear tape machine through the turning mechanism, and then the mask piece is conveyed to the ear tape machine through the conveyor belt. On the front of the first mask plate, finally, the mask sheet is placed into the mask plate of the ear band machine by pressing down by the air cylinder. The ear band machine then completes the welding of the ear band of the mask, edging, etc. to complete an ear band mask. Production of products.
This machine adopts PLC, touch screen control, single-phase motor for main conveyor belt, stepping motor turning, precise transmission, stable control and adjustable speed.
Face Mask Manufacturing Machine Features
Computer program control, high output, good stability and low failure rate.
photoelectric detection of raw materials to avoid errors and reduce waste.
It can produce one to four layers of mask body.
The machine has the function of total count and batch count. The number of batch count can be set arbitrarily.
Replacing the mold can produce masks of different sizes and styles.
the whole machine adopts aluminum alloy structure, beautiful and sturdy.
Technical parameters
1. The size of the machine is long, wide and high: the size of the whole machine is one according to the actual 1050cm * 150cm * 180cm
2. Voltage: AC220V 50-60HZ
3. Production efficiency: 30-40 pieces / min
4. Power: 10KW
technical parameters:
Imput raw materials, automatic feeding, nose line cutting / feeding, hemming welding, folding scene, forming welding, photoelectric detection, automatic slicing, finished product output, receiving tray sorting, full automation
| No. | Item | Parameter |
| 1 | size | 1050 (length) * 150 (width) * 180 (height) |
| 2 | Weight | weight ≤1500KG Ground load 350KG / ㎡ |
| 3 | Color | Color Sheet metal warm gray 1C, primary color of aluminum profile |
| 4 | Working power supply | 220VAC ± 5% 50HZ grounding protection rated power ≤10KW (including welding machine) |
| 5 | Compressed air | 0.4-0.6MP (clean water after dewatering, no oil, filtration, pressure stabilization), use flow rate is about 300L / min |
| 6 | Production efficiency | 30-40PCS / min (according to the actual debugging effect) |
| 7 | Product qualification rate | 99% (except for the original material and human operation) |
| 8 | Main accessories | Cylinder: AirTAC Screw guide rail: HIWIN / TBI PLC: Mitsubishi or Xinjie |
| 9 | Operating environment | General workshop environment is acceptable (no corrosive odor, no dust) |
Equipment use matters needing attention:
The machine should be installed on a flat and solid ground, and sufficient operation and maintenance space should be reserved around the machine
5.1 Environmental conditions
1. Temperature: The normal ambient temperature must be 5°C ~ 40°C.
2. Humidity: 30% ~ 90%.
3. Keep away from paint (gasoline), chemicals, acid, alkaline and explosive or flammable materials.
4. Avoid neighbouring machines that can cause vibration. Ambient lighting: above 300LUX
5.2 Installation notes
1. After the machine is positioned, adjust the foot cup of the machine and use the horizontal auxiliary tool until it is adjusted to the level.
2. Connect the power cord. This machine uses 220V single-phase, 50HZ power. It is strictly prohibited to connect 380V or other power sources that do not meet the requirements. Please pay special attention to the user! To ensure safety, the connection work must be completed by an electric professional, and a connection cable is provided. If self-equipped power plug is used, 2.5mm2 three-core cable must be used to correctly connect live wire (L), neutral wire (N) and ground wire (E).
